KitchenAid 3184330 Installation, With hot water dispenser in kitchen, View from top, Panel C

Installation

With hot water dispenser in kitchen.

I1 Determine the best faucet mounting position that will allow faucet spout to empty into sink. Check below sink to

assure that reinforcing ribs, support brackets or cabinet construction will not interfere with faucet mounting. Knock out plug from hole in sink or cut a hole in sink or countertop.

NOTE: It is recommended that only a licensed plumber or professional installer cut an opening in the sink or countertop.

When unpacking faucet, Do Not remove ureen tape from faucet

jj tubing oFtank tubing.

I bracket

Position tank vertically beneath faucet 1 I so that clear tubina from faucet

ureaches center cobper tubing on tank, and tank touches wall. Use a pencil to mark on the wall where the top of tank needs to be located. Set tank aside. Mark a second line 2-l/4” below the line. Position mounting bracket on wall so that bottom of mounting bracket is even with the lower line. Use two screws (and plastic anchors if attaching to dry wall) to fasten mounting bracket to wall. Hang tank on bracket.

Turn off main water supply. Turn on sink cold water faucet and allow all water to drain from line. Turn off faucet.

If water supply is copper, go to Step 9.

If water supply line is rigid metal, use a grounded electric drill or hand drill to drill a l/4” hole in the cold water line.

NOTE: Flexible ribbed tubing requires special connecting hardware available from your local plumbing supply.

green We

Lay faucet on flat surface with coiled tubing facing up. Using one hand to hold tubinn iust below faucet, carefullv

straighten tubing with other hand. Slide gasket z over tubing so that gasket is seated under base of faucet.

Install faucet with lever to the side or

Failure to do so may result in hot water scalding hand when operating lever.

lever to the side or behind spout

f#sjnk

View from top

I

			W’	19 I
					n	Turn saddle valve handle so piercing
compression				u		lance		does	not protrude.
	union\	T		Put seal on saddle				valve	and	position	assembly on
				vertical, cold water supply line.
				Align bottom clamp holes with holes in top clamp.
			compression Insert clamp screws. Attach one square nut to end
				of each clamo screw. Tiahten nuts evenlv and
DO Not	lengthen, twist or			firmlv,	keep&		bracketstarallel.			Do Not-
tightly	bend	tubes.		ovet%ghtdn clamp screws, copper tubing
Do Not remove green tags.
				could	be crushed.
		Use a compression union to connect
		the longer, l/4” tubing from the faucet					Product		Damage
I		I	tubina in the top of the
		to the back		Do	Not use		pipe sealing compounds.
tank (both are marked with green tape): Faucet
tubing	may be shortened		if necessary.	Pipe sealing			compounds			may get	inside
				dispenser and cause an unpleasant taste
				or smell.

J outlet.

green

We n

- \’ // IIt-

7 clear tubing fl

7

-

4 Piercing lance in closed position.

Hold gasket in position and insert tubing through gasket, then into mountina hole. From under

sink/cabinet, slide w&her then wing nut with flat side facing up over tubing. Check that lever is positioned to the side or behind spout and that spout is positioned to empty into sink. Tighten wing nut by hand until faucet is securely in position.

Top view		180” .-			Install	faucet	with
	)-.				lever	to the	side
0 0	0	n	.N	\	or behind spout
					\
0					\
	I	.			\

spoutlever

Connect clear tubing from faucet to H middle tank tube using clamp. Clear

tubing may be shortened, if necessary.

Electrical Shock Hazard Some water may remain in water supply pipe:

lIf an electric drill is used, it must be properly grounded to prevent severe or lethal shock if water should enter drill. Use only an electric drill with a 3-wire

cord connected to a grounded receptacle.

l Check with a qualified electrician if you are in doubt as to whether your electric drill is properly grounded.

Failure to follow these instructions could result in personal injury or death.

Assembly fits 318” through l-318”

O.D. copper or rigid metal line.

View from top

Slide brass sleeve into copper tubing fitting; use plastic sleeve if water

usup&y line-is not copper. Attach fitting to saddle valve outlet. Connect l/4” O.D. copper tubing (not supplied) to tubing fitting.

Do not seal the connections with sealing compounds.

Panel C