Use and care information
Your hot water dispenser uses a heating element to warm water in the tank to approximately 190°F when the temperature control is turned to the highest position. You can draw approximately 2 quarts of hot water at a time. As hot water is drawn from the tank, it refills with cold water, which is then heated. It takes approximately 15 minutes for a tank of cold water to heat to the maximum temperature.
Personal Injury Hazard
l Check that lever is to the side or behind faucet spout before using hot water dispenser.
l Do Not reach into or splash hot water on skin.
l Do Not let children operate hot water dispenser.
l Do Not leave children or infants unattended near hot water dispenser.
l Do Not use hot water from dispenser for bathing children, infants or pets.
Water from hot water dispenser can reach temperatures of approximately 190°F. Failure to follow these instructions may result in scalding or burns from hot water.
To get hot water from the tank: Push or pull faucet lever.
To stop water flow from faucet:
Release faucet lever and let it return to the vertical position.
Ways you can use your hot water ’ dispenser:
Your hot water dispenser water has many uses, including:
l To prepare instant foods and drinks that require 190°F maximum water for preparation (such as instant coffee, tea, hot chocolate, bouillon, soup, instant cereal, instant mashed potatoes, frosting mix, etc.).
l To get a fast start on cooking foods that require boiling (such as hard boiled eggs, fresh or frozen vegetables, meat cooking in liquid, dried soup, pasta, rice, hot cereals, packaged dinners with pasta, rice or potatoes).
l Loosening jar lids.
l Warming baby bottles. l Warming baby food.
l Filling hot water bottles.
l Peeling tomatoes or peaches. l Dissolving gelatin.
l Thawing frozen foods.
l Preparing vegetables for canning.
If you have very hard water, it may be necessary to occasionally clean the faucet screen to remove sediment buildup.
To remove the faucet screen:
1.Set hot water dispenser thermostat to “OFF.”
2.Hold lever down and drain hot water from tank. Release lever.
3.Unscrew nozzle from faucet spout.
4.Remove screen and flow director from inside nozzle.
To clean the screen and flow director:
1.Use a small brush and vinegar to remove deposits.
2.If deposits have hardened, soak screen and flow director in vinegar for
To replace faucet screen:
1.Insert flow director into nozzle. Then insert screen.
2.Position nozzle on end of faucet spout and carefully tighten by hand.
NOTE: Nozzle must be fully tightened for screen and flow director to be properly seated and for nozzle not to leak.
3.Check that faucet spout is positioned away from faucet lever. Hold lever down and check for leaks at nozzle. If nozzle leaks, remove nozzle and check that screen and flow director are properly positioned. Replace nozzle and check for leaks again.
4.Set hot water dispenser thermostat to “HIGH.”
On average, you will use your hot water dispenser to heat 7 to 8 cups of water per day. This uses only 19
However, if the hot water dispenser will not be used for an extended period of time, follow these instructions -
For short periods
For long periods of nonuse, seasonal storage or protection from freezing:
1.Turn hot water dispenser thermostat to the “OFF’position.
2.Unplug hot water dispenser power supply cord.
3.Hold down faucet lever and run water until water is cold.
4.Turn saddle valve handle clockwise to turn off water supply.
5.Place a
6.Remove drain plug with a 9116” wrench and allow all water to drain from tank.
6.Replace plug, but do Not overtighten.
drain plug
Product Damage
Fill tank with water and turn thermostat to “OFF” position before plugging hot water dispenser into power supply.
Failure to do so could cause hot water dispenser heater to overheat resulting in an unpleasant taste, black specks in water, and permanent damage to the heater seals.
1.Turn saddle valve handle counterclockwise to open water supply line.
2.Hold down faucet lever until tank is full (approximately 1 minute). When tank is full, water will flow from faucet spout. Release lever. Check for leaks.
3.Check that hot water dispenser thermostat is set to “OFF’ position.
4.Plug power supply cord into properly grounded outlet.
5.Set thermostat to “HIGH” position. Water in tank will reach maximum temperature in approximately 15 minutes and dispenser will be ready for use.
The water temperature is controlled by a thermostat on the tank. The thermostat has infinite settings between “OFF’ and “HIGH”and can be adjusted by rotating the thermostat knob clockwise for a higher temperature;
When the thermostat knob is turned to the “OFF’ position, the hot water dispenser will not heat the water. When the thermostat knob is turned to the “HIGH” position, the water will heat to approximately 190°F.
It is recommended that the thermostat be set to the “HIGH” position for the best performance. However, under certain conditions, it is possible that you will see vapor coming out of the faucet or hear a boiling noise when the thermostat is set to “HIGH.” If this occurs, lower the thermostat setting to a position that eliminates the vapor or noise.
Problem
Water is not hot.
Vapor appears or dispenser makes boiling water noises.
Hot water drips or sputters from faucet.
Water does not flow from faucet.
Leaking saddle vatve.
Water has a “rottenegg” taste.
Solution
A. Check that the circuit breaker is not tripped or the house fuse blown. B. Check that power supply cord is plugged into wall receptacle.
C. Check that hot water dispenser thermostat is set to “HIGH” position. D. Cold water in tank is stiil being heated. Wait 15 minutes and check
temperature again.
Adjust hot water dispenser thermostat to a lower setting that eliminates the vapor or noise.
A. Check that tubing is not bent or kinked.
6.Adjust hot water dispenser thermostat to a lower setting that eliminates the drips/sputters.
C. Checkthat nozzle screen is not clogged. See “Maintaining your hot water dispenser,” Panel E.
D. Check for proper installation of copper tubing from faucet to storage tank and from faucet to cold water line. See Steps
Check that water supply valve is open.
Tighten saddte valve clamp screws evenly and firmly, keeping both halves of bracket parallel. Do Not deform tubing.
A. Hot water dispenser is attached to hot water line. Attach to cold water line.
B. Install a water filtration system on cold water line to dispenser.
