Electrical ground is required. See Electrical requirements.
DO NOT install dishwasher over carpeted flooring.
Proper electrical, drain and water supply lines must be available or must be installed as specified within
Product Damage Protect dishwasher and water lines leading to dishwasher against freezing.
Failure to do so could cause inlet valve, water lines leading to dishwasher, water lines in dishwasher and drain to rupture.
Such ruptures are not covered by warranty.
For installations where the dishwasher will be left unused and subjected to freezing temperatures, it must be prepared as outlined in your Use and Care Guide.
IMPORTANT: Observe all governing codes and ordinances.
T!l
to 35” max. underside counter height.
If
*26”
+
Corner location - 2” min. door to cabinets or wall
Cut | 1” holes | for | Grommet | |||
water, | drain | and | ||||
electrical | lines | required | for | |||
within |
| shaded | area. | electrical | ||
The | unshaded | cable | hole | |||
cut in metal | ||||||
area | must | be | free | cabinets | ||
of | pipes, | drain |
|
| ||
hose | or | wires. |
|
|
de-24” opening width A
Figure I
depth4
Figure 2
‘Whisper Quiet insulation compressed.
cabinet 36”
depth countertop height
LIE
Electrical Shock Hazard
1Electrical wiring and components must not contact any plumbing material or drain hose.
1Electrical wiring, water supply line and drain line must not contact any expose terminals of dishwasher wiring.
1Cabinet opening must completely enclose sides, top and back of dishwasher. A side panel and wood top are available from your KitchenAid dealer to install your dishwasher at the end of a cabinet.
Failure to follow these instructions may result in qersonal injury from exposed Miring.
Page 2
Personal Injury/Product Damage Hazard
Avoid opening dishwasher door before dishwasher is installed.
Dishwasher, before it is installed, may tip over when door is opened, resulting in personal injury or product damage.
Parts supplied for installation:
2 counterlop anchor screws
Remove screws taped to upper right hand mounting bracket.
Check that all parts were included.
Tools and materials needed for installation:
l | electric | drill | l |
| shutoff | valve |
|
| ||||||
l | Phillips |
|
| l |
| supply | line | fittings | ||||||
| screwdriver |
| l |
| 1,3/8” |
| NPT | street | ||||||
l | 2 adjustable |
|
|
| elbow |
| (2 | for |
|
| ||||
| wrenches | for |
|
| galvanized |
| line) | OR | ||||||
| copper | fittings |
|
| 90” compression |
| ||||||||
| OR | 2 pipe |
|
|
| elbow |
| with | 3/S” | NPT | ||||
| wrenches | for |
|
| at one end for copper | |||||||||
| galvanized | or |
|
| line |
|
|
|
|
|
|
| ||
| iron | fittings |
| l | 9/l 6”, I.D. heat- and | |||||||||
l | pliers |
|
|
|
|
| ||||||||
l | measuring | tape |
|
| hose |
| and | clamps | OR | |||||
l |
|
|
| 5/8”, |
| |||||||||
|
|
| tubing | and | fittings | |||||||||
| screwdriver |
|
|
| ||||||||||
. | 3,411nut | driver | or | l |
| lo”, |
| 5/8” | 0.D. | Soft | ||||
| socket | wrench |
|
| copper | tubing | if | high | ||||||
|
|
| loop | drain | is | needed. | ||||||||
l | wire | cutters |
|
| ||||||||||
|
| (See | Page | 3.) |
|
| ||||||||
| level |
|
|
|
|
|
| |||||||
l | bit or hole l |
| 314 | II |
|
| . | relief | ||||||
. ,,, drill |
|
| strain | |||||||||||
| saw |
|
|
| l |
| tubing | cutter |
|
| ||||
|
|
|
|
|
| compound | ||||||||
l | l/8” | drill bit | l |
| ||||||||||
| l |
|
| |||||||||||
l | square |
|
|
|
|
| ||||||||
|
|
|
| connectors |
|
|
|
| ||||||
| 112” O.D. copper |
|
|
|
|
|
| |||||||
l |
|
| electrical | tape |
| |||||||||
| tubing | OR | 318” | l |
| |||||||||
|
|
|
|
|
|
|
|
|
|
|
We