Electrical requirements

Before you start...

Your safety and the safety of

others is very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill

or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING”. These words mean:

DANGER

You can be killed or seriously injured if you don’t immediately follow instructions.

WARNING

You can be killed or seriously injured if you don’t follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

IMPORTANT: Observe all governing codes and ordinances.

Proper installation is your responsibility. Make sure you have everything necessary for correct installation. It is the responsibility of the installer to comply with the clearances specified.

Check the location where the hood liner will be installed. The location should be away from strong draft areas, such as windows, doors, and strong heating vents.

Mobile home installation

The installation of this hood liner must conform to the Manufactured Home Construction Safety Standards, Title 24 CFR, Part 328 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD, Part 280) or when such standard is not applicable, the Standard for Manufactured Home Installation

1982 (Manufactured Home Sites, Communities and Setups) ANSI A225.1/NFPA 501A*, or latest edition, or with local codes.

WARNING — TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable Codes and Standards, including Fire Rated Construction. Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent back drafting. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society of Heating Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities.

When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

Ducted fans must always be vented to the outdoors.

WARNING — To reduce the risk of fire, use only metal ductwork.

This unit must be grounded.

This hood liner must be used with Exterior Blower Models:

KPEC992M rated for 900 cfm (25.5 cm/m) or,

KPEU722M rated for 1200 cfm (34.0 cm/m).

Both models are available from your dealer.

This fan suitabable for use with solid-state speed controls.

Tools and materials needed for installation:

•compass or 11" (27.9 cm) circle template

•flat blade screwdriver

•Phillips screwdriver

•pliers

•metal snips

•drill

•1-1/4" (3.0 cm) dia. drill bit

•5/16" (7.9 cm) dia. drill bit

•pencil

•ruler

•saber saw or keyhole saw

•duct tape

•3/4" (10.0 mm) U.L.- or C.S.A.-Listed strain relief

IMPORTANT: Observe all governing codes and ordinances.

The Exterior Blower is connected to the fused electrical system at the wiring box of the Hood Liner. refer to the Installation Instructions supplied with the Exterior Blower model for the electrical system.

It is the customer’s responsibility:

•To contact a qualified electrical installer.

•To assure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70

— latest edition*, or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No.0-M91 - latest edition** and all local codes and ordinances.

A 120-volt, 60 hz, AC-only, fused electrical system ia required. A separate 15-amp circuit is recommended.

A separate ground wire must be used. It is recommended that a qualified electrician determine that the ground path is adequate..

Do not ground to a gas pipe.

Check with a qualified electrician if you are not sure range hood is properly grounded.

Do not have a fuse in the neutral or ground circuit.

The connection at the hood liner wiring box must be with copper wire only.

IMPORTANT:

Save Installation Instructions for electrical inspector’s use.

The 120-volt supply to the hood liner wiring box should be connected directly to the fused disconnect (or circuit breaker) box through flexible armored or nonmetallic sheathed copper cable. A U.L.- or C.S.A.-listed strain relief must be provided at each end of the power supply cable. Wire sizes (COPPER WIRE ONLY) and connections must conform with the rating of the appliance as specified on the model/serial rating plate.

Wire sizes must conform to the requirements of the National

KPEC992M specifications

The KitchenAid KPEC992M is an innovative and versatile kitchen appliance that brings professional-grade performance to home cooking. Designed with both functionality and aesthetics in mind, this product embodies the brand's legacy of quality craftsmanship.

One of the standout features of the KPEC992M is its powerful motor, which delivers remarkable efficiency and speed. With multiple speed settings, users can easily adjust the performance to suit a variety of cooking tasks. This makes it ideal for everything from whipping cream to kneading heavy dough. The unique planetary mixing action ensures that all ingredients are thoroughly combined, making the mixing process seamless and effective.

Another significant characteristic of the KitchenAid KPEC992M is its large-capacity bowl, which accommodates generous quantities of ingredients. This is particularly useful for family gatherings or meal prep, as it allows users to mix larger batches without needing to do multiple rounds. Additionally, the bowl is designed with a convenient handle, making it easy to maneuver and pour.

The KPEC992M also features a robust construction that promotes durability and longevity. Made with high-quality materials, it is designed to withstand the rigors of daily use while maintaining its sleek appearance. The unit comes in a variety of stylish colors, allowing it to complement any kitchen décor.

One of the highlighted technologies in the KPEC992M is its attachment hub, which is compatible with a wide range of KitchenAid accessories. This versatility enables users to expand their culinary capabilities, transforming the mixer into a food processor, pasta maker, or even a juicer. The adaptability of the KPEC992M makes it a valuable addition to any kitchen setup.

Furthermore, safety features have not been overlooked. The mixing bowl locks securely into place, and there are built-in mechanisms to prevent operation when the bowl is not properly positioned. This attention to detail provides peace of mind for users, ensuring a safe cooking experience.

In summary, the KitchenAid KPEC992M is a robust and versatile kitchen mixer that combines power, efficiency, and style. With its numerous features, including multiple speed settings, large-capacity bowl, and compatibility with various attachments, this appliance caters to both novice cooks and seasoned chefs alike. Its durable construction and safety mechanisms further enhance its appeal, making it a wise investment for those who cherish culinary exploration.