INSTALLATION INSTRUCTIONS

Unpack the Ice Maker

WARNING

Excessive Weight Hazard

Use two or more people to move and install ice maker. Failure to do so can result in back or other injury.

Removing Packaging Materials

Remove tape and glue from your ice maker before using.

The ice maker must be installed in an area sheltered from the elements, such as wind, rain, water spray, or drip.

When installing the ice maker under a counter, follow the recommended opening dimensions shown. Place electrical and plumbing fixtures in the recommended location as shown.

NOTES:

Be sure the power supply cord is not pinched between the ice maker and the cabinet.

Be sure the water supply line is not pinched between the ice maker and the cabinet.

Be sure the drain line (on some models) is not pinched between the ice maker and the cabinet.

To remove any remaining tape or glue from the exterior of the ice maker, rub the area briskly with your thumb. Tape or glue residue can also be easily removed by rubbing a small amount of liquid dish soap over the adhesive with your fingers. Wipe with warm water and dry.

Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue. Do not use chlorine bleach on the stainless steel surfaces of the ice maker. These products can damage the surface of your ice maker.

Cleaning Before Use

34"

(86.4 cm)

Min.

34¹⁄₂"

(87.6 cm)

Max.

11¹⁄₂" (29.2 cm)

3¹⁄₂" 9"

(8.9 cm)(22.9 cm)

A

28¹⁄₂"

(72.4 cm)

After you remove all of the packaging materials, clean the inside of your ice maker before using it. See the cleaning instructions in the “Ice Maker Care” section.

Location Requirements

To ensure proper ventilation for your ice maker, the front side must be completely unobstructed. The ice maker may be closed-in on the top and three sides, but the installation should allow the ice maker to be pulled forward for servicing if necessary.

Installation of the ice maker requires a cold water supply inlet of ¹⁄₄" (6.35 mm) OD soft copper tubing with a shutoff valve and either a gravity-drain system or condensate pump to carry the water to an existing drain.

Choose a well ventilated area with temperatures above 55°F (13°C) and below 110°F (43°C). Best results are obtained between 70°F (21°C) and 90°F (32°C).

B

24"

(60.1 cm)

15"

(38.1 cm)

A. Recommended location for electrical and plumbing fixtures

B. Floor level

Choose a location where the floor is even. It is important for the ice maker to be level in order to work properly. If needed, you can adjust the height of the ice maker by changing the height of the leveling legs. See “Leveling.”

4

Page 4
Image 4
KitchenAid W10206423A Installation Instructions, Unpack the Ice Maker, Location Requirements, Removing Packaging Materials

W10206423A specifications

The KitchenAid W10206423A is a highly versatile and efficient appliance that enhances the culinary experience in any modern kitchen. Designed with attention to detail, this kitchen tool boasts several features and technologies that make it a must-have for both amateur cooks and professional chefs alike.

One of the standout features of the KitchenAid W10206423A is its powerful motor, which provides superior mixing capabilities. With an impressive wattage, the motor ensures consistent results whether you are whipping, kneading, or blending ingredients. This heavy-duty performance means you can tackle even the most demanding recipes with ease, making it an indispensable ally for baking, cooking, or food preparation tasks.

Equipped with a range of speed settings, the Kitchenaid W10206423A allows for personalized control over mixing techniques. From slow stirring for gentle ingredients to high-speed whipping for airy mixtures, the adjustable speeds provide the flexibility needed for a variety of recipes. This feature also minimizes splatter and promotes thorough ingredient incorporation, ensuring that your dishes yield professional-quality results.

Another characteristic that sets the KitchenAid W10206423A apart is its robust construction. Crafted from durable materials, this kitchen appliance is built to withstand the rigors of daily use. The design not only contributes to its longevity but also makes it easy to clean after use, enhancing your overall kitchen experience. The sleek design fits seamlessly in any kitchen décor, combining practicality with style.

Additionally, the KitchenAid W10206423A comes with a selection of attachments that broaden its functionality. From dough hooks to whisk attachments, these tools enable users to expand their culinary repertoire. Whether you're making bread, whipping cream, or mixing cake batter, the versatility of attachment options allows the appliance to adapt to various cooking needs.

In terms of safety, the KitchenAid W10206423A incorporates built-in features that ensure safe operation. The appliance is designed with a secure locking mechanism to prevent accidental start-ups, giving users peace of mind while they work.

In summary, the KitchenAid W10206423A is a powerful and adaptable kitchen appliance that caters to the needs of a diverse range of cooking tasks. With its robust motor, adjustable speed settings, durable construction, and versatility provided by various attachments, this model stands as an excellent investment for anyone looking to elevate their culinary skills. Whether you are a seasoned cook or just beginning your culinary journey, the KitchenAid W10206423A is sure to become an essential tool in your kitchen.