Optional 3-wire connection

Use for direct wire or power supply cord where local codes do not permit connecting cabinet-ground conductor to neutral wire.

1.Remove center terminal block screw.

2.Remove neutral grounding wire (green with yellow stripes) from external ground conductor screw. Connect appliance ground wire and the neutral wire (white or center wire) of power supply cord/cable under center, silver-colored terminal block screw. Tighten screw.

3.Connect the other wires to outer terminal block screws. Tighten screws.

4.Tighten strain relief screws.

5.Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw.

6.Connect a separate copper ground wire from the external ground conductor screw to an adequate ground.

A

B

C

D

A. External ground conductor screw

B. Neutral grounding wire (green with yellow stripes) C. Neutral wire (white or center wire)

D. Grounding path determined by a qualified electrician

VentingRequirements

WARNING

Fire Hazard

Use a heavy metal vent.

Do not use a plastic vent.

Do not use a metal foil vent.

Failure to follow these instructions can result in death or fire.

WARNING: To reduce the risk of fire, this dryer MUST BE EXHAUSTED OUTDOORS.

4" (10.2 cm) heavy metal exhaust vent and clamps must be used. DURASAFE™ vent products are recommended.

DURASAFE™ vent products can be purchased from your dealer or by calling Whirlpool Parts and Accessories. For more information, see the “Assistance or Service” section of this manual.

The dryer exhaust must not be connected into any gas vent, chimney, wall, ceiling, or a concealed space of a building.

Do not use an exhaust hood with a magnetic latch.

Do not install flexible metal vent in enclosed walls, ceilings or floors.

Use clamps to seal all joints. Exhaust vent must not be connected or secured with screws or other fastening devices which extend into the interior of the duct. Do not use duct tape.

IMPORTANT: Observe all governing codes and ordinances.

Improper venting can cause moisture and lint to collect indoors, which may result in:

Moisture damage to woodwork, furniture, paint, wallpaper, carpets, etc.

Housecleaning problems and health problems.

Use a heavy metal vent. Do not use plastic or metal foil vent.

Rigid metal vent is recommended to prevent crushing and kinking.

Flexible metal vent must be fully extended and supported when the dryer is in its final position. Remove excess flexible metal vent to avoid sagging and kinking that can result in reduced airflow and poor performance.

An exhaust hood should cap the vent to prevent rodents and insects from entering the home.

Exhaust hood must be at least 12" (30.5 cm) from the ground or any object that is in the path of the exhaust (such as flowers, rocks or bushes, etc.).

If using an existing vent system, clean lint from the entire length of the system and make sure exhaust hood is not plugged with lint. Replace any plastic or metal foil vent with rigid metal or flexible metal vent.

13

Page 13
Image 13
KitchenAid YKEHS01P manual VentingRequirements, Optional 3-wire connection

YKEHS01P, KEHS01P specifications

The KitchenAid KEHS01P and YKEHS01P stand mixers are emblematic of KitchenAid's commitment to quality, durability, and innovative design in kitchen appliances. These stand mixers have become essential tools for both amateur home bakers and professional chefs, bringing versatility and performance to every kitchen.

One of the most notable features of the KEHS01P and YKEHS01P is their powerful motor. With a robust engine that delivers reliable torque, these mixers can handle a wide range of tasks, from whipping egg whites to kneading thick bread dough. This level of power ensures that users can mix even the heaviest of ingredients effortlessly.

Both models come equipped with the signature 10-speed slide control, which allows for precise adjustments to suit different mixing techniques and recipes. Whether it’s a slow stir, a moderate mix, or a fast whip, the seamless transition between speeds provides optimal control over the mixing process. This feature is especially beneficial when dealing with delicate ingredients that require a gentle touch.

The tilt-head design of the KEHS01P and YKEHS01P makes it easy to access the mixing bowl and change attachments, allowing for quick ingredient additions and simple cleaning. The mixers are compatible with a wide range of accessories and attachments that expand their functionality, from pasta makers to food grinders, enhancing their versatility in the kitchen.

Another key characteristic of these stand mixers is their sturdy construction. Made with a durable metal housing, the stand mixers provide stability during use and ensure long-lasting performance. Their compact yet powerful design means they can easily fit into any kitchen countertop without sacrificing functionality.

The mixing bowl included with these models is typically a generous 4.5-quart capacity, perfect for preparing large batches of dough or batter. The stainless-steel bowl is not only easy to clean but is also designed to resist rust and wear over time, adding to the longevity of the product.

In addition to functionality, style is not overlooked. KitchenAid offers a variety of colors and finishes, allowing users to find a model that fits their kitchen aesthetic.

Overall, the KitchenAid KEHS01P and YKEHS01P models embody a blend of power, precision, and style. They are designed to inspire culinary creativity while making the baking and cooking experience enjoyable and efficient. With their impressive features and reliable performance, these stand mixers are truly a worthy investment for anyone who loves to cook or bake.