8.Make sure the speakers in each room are connected in phase with the amplifier + going to the speaker +. Out of phase speakers give unstable imaging and poor bass response.

9.Connect the AC power into an outlet than can supply at least six amps (750 watts) dedicated to each KES400 or KES600.

10.After the amp has been turned on adjust the “SENS” pot on the rear of the amplifier if necessary. The “SENS” adjustment can be adjusted up (clockwise) to make the amp less susceptible to be turned on due to nuisance noise and hum. If it is adjusted too high, the amp may delay turn on or turn off during a quiet music or speech passage.

Caution: Never listen to sound that is distorted. If distorted sound is heard, turn the volume down immediately or speaker and/or amplifier damage could occur that is not covered by the warranty. If this problem persists, contact your dealer.

User Adjustments and Service: There are no user adjustments inside the KES400 or KES600. Your installer may make certain gain and sensitivity level adjustments on the rear panel.

Caution: The KES400 or KES600 contains no user serviceable parts, so do not attempt to open or repair the KES amp. Refer servicing to a qualified technician only or contact the factory for information.

Troubleshooting

If a problem is encountered with the KES400 or KES600 amplifier, the most expedient procedure is to locate the problem and if possible repair it before requesting service. Be sure to carefully check other system components such as controllers, CD players, volume controls, wiring, speakers, etc. that may be at fault.

Installation

Installing the amplifier should be relatively easy. With a bit of planning, this amplifier will give trouble free service for years.

1.The most important consideration when installing the KES400 and/or KES600 is cooling. This amplifier has a lot of power packed into a small chassis size. When installing it in an equipment stack, it should be the top component. It needs at least 3"-5" of space above the amplifier to allow for adequate convection cooling.

2.When installing the KES400 and/or KES600 in a rack we suggest adding a 3-1/2" blank above and below the amplifier. In multiple KES400 and KES600 installations, plan for a 3-1/2" blank (double) between each amplifier and a 3-1/2" blank on the top and bottom. Amplifiers should always be the top components in a rack system.

3.The KES400 and KES600 are available as an optional 19" EIA rack mount style.

4.Never operate a KES400 or KES600 on its side, as the cooling potential drops significantly when operated on the side.

5.Connect the KES400 or KES600 RCA inputs to the source component outputs with good quality, short as possible RCA jack cables. Connect each channel individually.

6.Connect the KES400 or KES600 speaker outputs to speakers using good quality speaker wire. Minimum 16 gauge copper wire is recommended with 14 gauge minimum for runs over 30' (10m). Fire-rated wire may be required if installing wires inside walls, ceilings or floors.

Note: Ideally the KES400 and KES600 amplifiers like 6-8 ohm loads. Connecting to 4-ohm loads won't hurt the amplifier, but the channels connected to 4-ohm loads may occasionally shutdown due to overloading. Never connect any KES400 or KES600 amplifier to less than 4 ohms.

7.Individually adjust the channel gains as required. Ideally, all gains are fully on (fully clockwise).

Page 2 Page 4
Page 3
Image 3
Knoll KES400, KES600 warranty Installation
Page 2 Page 4

KES400, KES600 specifications

The Knoll KES400 and KES600 are innovative office furniture solutions designed to enhance productivity and comfort in workplace environments. These desks and systems provide a seamless blend of functionality and aesthetics, meeting the dynamic needs of modern workspaces.

The KES400 offers a robust yet elegant design, featuring a height-adjustable surface that allows users to shift between sitting and standing positions effortlessly. This adaptability promotes better posture and reduces the risks associated with prolonged sitting. Coupled with its sturdy frame, the KES400 is built to withstand heavy usage, making it an ideal choice for busy office settings.

In addition to its ergonomic design, the KES400 incorporates advanced technologies that elevate user experience. Integrated cable management systems ensure a clean and organized workspace, minimizing visual clutter and facilitating easier access to power sources. The customizable surface finishes and materials allow organizations to tailor the desk to their brand aesthetics and individual needs.

On the other hand, the KES600 takes it a step further by incorporating collaborative features. Designed for teamwork, this system promotes communication and interaction among team members. The KES600 features modular components that can be easily reconfigured to suit various group sizes and work styles. This flexibility is particularly beneficial in an era where collaborative work is becoming increasingly prominent.

Both models utilize eco-friendly materials, aligning with sustainable practices that many organizations are adopting. The use of recycled components and low-emission manufacturing processes not only reduces the environmental impact but also contributes to healthier office spaces.

Additionally, the KES400 and KES600 come equipped with smart technology options, allowing users to integrate their devices seamlessly. This connectivity enhances the efficiency of workflow and supports the various technologies employed in contemporary workplaces.

Overall, the Knoll KES400 and KES600 are not just pieces of furniture; they represent a philosophy of creating supportive and adaptable work environments. With their ergonomic designs, sustainability, and integration of technology, these models are poised to meet the evolving demands of the modern workforce, thereby contributing to enhanced productivity and employee satisfaction.
Top Page Image Contents