Setting the impedance matching jumpers:

Each of the VC100im volume controls needs to have the jumpers correctly set. The two jumpers are located on the rear side of the volume control. Both channels on all volume controls in this system should be set to the same jumper setting.

The jumper setting is determined by three factors:

X8

1. The speaker impedance (all the speakers in

X4

this system should have the same

 

impedance).

 

2. The number of volume controls connected

X2

to one stereo amplifier.

X1

3. The minimum speaker load impedance the

 

amplifier can handle.

 

In the illustration both jumpers are shown set in

X8

the X4 position. Ideally, all volume controls in

this system should have their jumpers set to

X4

the same correct position. 4 and 8 ohm

 

speakers can safely be combined in a system. Use

 

the 4 ohm settings. The jumper needs to be

X2

pushed on as far as it goes.

X1

 

To determine the correct jumper or shunt position, use the chart below.

When using amps or receivers with 8 ohm capacity

Jumper setting

X1

X2

X4

X8

4 Ohm speakers

don’t

1 pair

2 pair

4 pair

 

 

 

 

 

8 Ohm speakers

1 pair

2 pair

4 pair

8 pair

 

 

 

 

 

When using amps or receivers with 4 ohm capacity

Jumper setting

X1

X2

X4

X8

4 Ohm speakers

1 pair

2 pair

4 pair

8 pair

 

 

 

 

 

8 Ohm speakers

2 pair

4 pair

8 pair

16 pair

 

 

 

 

 

As an example, if the amplifier has 4-ohm capability with 7 pairs of 8 ohm speakers to be installed, set all VC100im jumpers to X4.

Connection and trim-out:Remove about ¼” of insulation from the ends of all wires connected to the volume control and twist the exposed strands. The stereo amplifier or receiver outputs (left and right) are connected to the VC100im top connector labeled “INPUT”. Be very careful to observe the correct polarity. The VC100im uses independent floating grounds so bridged amplifiers can be used safely.

The VC100im is rated for use with maximum 100 watt per channel amplifiers. DO NOT use higher-powered amplifiers with this product for safety reasons.

Wire from the amplifier speaker terminals is always wired in parallel to all VC100im volume controls. To make the installation look neat and tidy, we suggest using one or more WT6 connection strips. When connecting to the amp make sure its power is switched off. Again strictly observe wiring polarity.

Connect the four position connectors labeled “OUTPUT” to the stereo speakers they will control. Again series and parallel speaker wiring is acceptable so that the impedance the volume control sees is between 4 and 8 ohms. Be sure to strictly observe polarity, as incorrect polarity will result in poor bass performance.

When installing the volume control into the wall, we suggest moving any inside wall fixtures such as vapor barriers away from the autotransformers if possible.

Page 1 Page 2
Page 2
Image 2
Knoll Systems VC100IM warranty Setting the impedance matching jumpers, X4 position. Ideally, all volume controls
Page 1 Page 2

VC100IM specifications

The Knoll Systems VC100IM is a prominent choice in the realm of audio-visual solutions, particularly favored for its impressive capabilities in both commercial and residential applications. This cutting-edge device is engineered to meet the demands of today's dynamic audiovisual environments, boasting a range of features that set it apart from traditional models.

One of the notable main features of the VC100IM is its high-definition video processing capability. The system supports various resolutions, including 1080p and 4K, ensuring crystal-clear image quality, which is critical for professional presentations and home theater experiences alike. This versatility makes it suitable for classrooms, boardrooms, and media-centric environments.

Another significant characteristic of the VC100IM is its robust connectivity options. The device incorporates multiple HDMI ports, USB interfaces, and support for legacy connectors, enabling seamless integration with a wide variety of sources. This flexibility facilitates easy connectivity with laptops, projectors, and streaming devices, allowing users to quickly and efficiently set up their AV systems without the hassle of complicated wiring.

Furthermore, the VC100IM features advanced audio technologies, including Dolby Digital decoding and sophisticated sound processing. This ensures that audio playback is not only clear but immersive, providing an engaging experience for users. The inclusion of built-in amplification means that external speakers are not always required, making the VC100IM an excellent option for space-constrained installations.

In terms of user experience, the VC100IM is equipped with an intuitive interface and a user-friendly remote control. This allows users to navigate through settings and switch between inputs easily, enhancing the overall usability of the system. Additionally, the device supports wireless connectivity options, enabling users to mirror devices and stream audio or video content directly from smartphones and tablets without the need for physical connections.

Overall, the Knoll Systems VC100IM stands out due to its excellent combination of advanced video and audio processing, versatile connectivity options, and user-centric design. Whether in a corporate setting or for home entertainment, this system offers a powerful and flexible solution that caters to a variety of audiovisual needs. Its ability to adapt to changing environments and technologies makes it a forward-thinking choice for those seeking high-quality visual experiences.
Top Page Image Contents