Manuals / Kodak / Computer Equipment / Scanner

Kodak i600 Error handling, Enable scanning, Initiate polling, Feed documents, Disable scanning

Models: i600

1 83

Download 83 pages 6.6 Kb

Page 7

Enable scanning	The host must issue a Scan command to enable scanning before
	documents can be transported through the scanner. If scanning has not
	been enabled, the feeder and transport system will not turn on.
Initiate polling	Initiate host system polling of the scanner to ensure scanned document
	images are transferred from the image buffer to the host system.
	Polling should continue until scanning is disabled.
	For more information see the sections entitled, “Controlling image
	transfer order” and “Image header information” later in this chapter.
Feed documents	Feed documents according to the instructions found in the Kodak i600
	Series Scanners User’s Guide.
Disable scanning	Scanning is disabled to allow the host to download configuration/setup
	changes between jobs and to handle certain types of errors.
	Scanning is also disabled when one of the following conditions occur:
	•	The scanner is first powered on using the power switch.
	•	A 1394 bus device Reset command is executed.
	•	A scanner unique End-of-Job command is issued by the host
		computer.
	•	Transport timeout is set to End-of-Job.
	•	An error occurs requiring fault recovery.
	NOTE: When scanning is disabled, documents cannot be scanned until
		the host enables scanning.
Error handling	The scanner recognizes and reports a variety of error conditions.
	Some errors are reported to the host (via the 1394 interface) or via the
	LEDs on the scanner while others are reported to both the host and the
	LEDs.

An error (via the 1394 interface) is defined as either a current or deferred error.

A current error results from a problem in processing the current scanner command. This can include sending an invalid command, trying to read from an empty image buffer, or an end-of-job condition. Since one or more errors may be pending at any time, current errors are reported first.

A deferred error results from an error condition within the scanner, such as a document jam. Deferred errors are reported after current errors.

NOTE: Low-level 1394 commands and information are handled by the device driver. The following information is provided for reference only.

A-61504 April 2007

2-3

Image 7

Kodak i600 manual Error handling, Enable scanning, Initiate polling, Feed documents, Disable scanning

Contents

Page About this manual 1 IntroductionBB.tif Image outputsFB.tif FC.jpgback black and white FG.jpg2 Best Practices Scanner setup Initiate polling Error handlingEnable scanning Disable scanningBlack and white only - duplex Controlling image transfer orderColor only - duplex Dual stream - black and white and grayscale - duplex Dual stream - black and white and color - duplexPage Jam and fault recovery Image file storage locations Print string formatting Electronic color dropoutContrast% = Threshold = Color Filter = Red Dropout  Near Complete Dropout Red dropoutRed Dropout - Complete Dropout Blue Dropout  Near Complete Dropout Green Dropout  Complete DropoutGreen Dropout  Near Complete Dropout Blue Dropout  Complete DropoutImage header information Patch Detect  indicates whether or not the scanner detected a toggle Zone processingpatch on the document side independent. If a toggle patch appears on Installation Overview Terminology and features 3 Using the TWAIN DatasourceValidation Tool Accessing the ScanValidation ool Select StartProgramsKodakDocument ImagingScanThe TWAIN interface is divided into three main sections Black and White Document Black and White Document OCR Quality The main Kodak Scanner windowColor Document Color Document OCR Quality Color Photograph Two Sided scans the front and back of the document About displays the scanner’s version and copyright information Information iconsThe Image Settings window Preview area Toolbar buttonsInformation icons Page Compression - allows you to reduce your electronic image size Part of the document if you select Document Automatically Detect and StraightenAutomatically Detect or Document Manually Select Origin x, ySize W, H if you select Document Automatically Detect and Straighten none180 degrees noneLandscape 90 degreesImage Settings - Adjustments tab - Black and White Filters Image none Filters Noise noneNo Noise Filter Used Enhancements tab Image SettingsThe options available on the Enhancements tab depend on the Scan as Input document is - select Two Sided, One Sided - Front, or One Advanced tabOne indicates you want the scanner to create one image Delete removes the selected image type Add adds an image type to the bottom of the configuration listToolbar buttons Change allows you to change the currently selected image typeSensitivity Content Settings tabA-61504 April 3-2210. Select Sides Both Color 24-bit 5. Select Images per side One - based on document content4. Select Input document is Two Sided select Grayscale9. Select Sides Both Color 24-bit Creating multiple images for each side of a document5. Select Images per side Multiple make sure Black and White 1-bit is selected4. Select Images per side One Creating different settings for each side of a document3. Turn on the Different settings per side option 2. Select Input document is Two SidedInformation icons The Device Settings windowPaper source Device - General tabDocument Feeder A-61504 April NOTE Using this option will decrease overall throughputDiagnostics - displays the Diagnostics tab 3-28Device - Printer tab Date Format MMDDYYYY DDMMYYYY YYYYMMDD DDD Julian YYYYDDD Julian Feed Direction none Ultrasonic detectionContinue Scanning the scanner will continue to scan Patch Code Information for Kodak Document Scanners for complete Device - Patch tabCreating a new Setting Shortcut 10. Select Save As. The Save As window will be displayed 4. Select the appropriate options on the General tab6. Click Preview to review the resulting image 9. Select Home to return to the main Kodak Scanner window2. Select Settings to display the Image Settings window Diagnostics - General tab The Diagnostics windowTests Refresh displays the scanner time Scanner Time3-39 A-61504 April 3. Click OK when the calibration is successfulFor changes to take effect, you must restart your application 3-40Images Toolbar buttons LogsRefresh redisplays the log The main ISIS Driver window 4 Using the ISIS DriverMain tab Image ModeOff no patches will be used A-61504 April A-61504 April Image Orientation Layout tabGeneral options when Fixed to Transport or Relative to Document is selectedand grayscale images that is widely used by scanners, digital cameras Color optionsNormal select when you are scanning a stack of documents of Scanner tabDocument Feeder options TimeoutPower Saver Multi-feed DetectionOperations Detect OnlyStop Feeder and Transport stops the feeder and the transport and Page Low documents require only a small amount of color to be saved as Color ContentLearn Color Dropout Dropout tabBlack and White or Grayscale is selected Black and White, Grayscale and Color you want to delete. The Blank Image DetectionDefining your print string Print on the front of document before scanning enables theImprinter tab ModeUnits - select Inches, Centimeters or Pixels Operator Log tabDisplays information about your scanner and driver About tabA-61504 April A-61504 April 4-20Area Previous Location/Name Appendix A TWAIN Image Processing TerminologyFeature Camera Selections Feature Color TablesOptions Feature CroppingFeature Polarity Options