Manuals / Kodak / Computer Equipment / Scanner

Kodak i600 manual 3-22, A-61504 April

Models: i600

1 83

Download 83 pages 6.6 Kb

Page 39

•Custom: allows you to manually adjust the Color amount and/or Color threshold.

NOTE: When setting Sensitivity values, it is suggested that you start with the Medium option and scan a typical job set. If too many documents were returned as color/grayscale vs. black and white, then change to the High option and re-run the job. If too few documents were returned as color/grayscale vs. black and white, then change to the Low option and re-run the job. If none of these options provide the desired result, select Custom to manually adjust Color amount and/or Color threshold. Custom also allows access to the Learn mode which provides a method for the scanner to analyze documents and recommend settings.

Color amount — the amount of color that needs to be present in a document before it will be saved as color/grayscale. As the value of Color amount increases, more color pixels are required. The options range from 1 to 200.

Color threshold — the color threshold or saturation (i.e., pale blue vs. dark blue) at which a given color will be included in the color amount calculation. A higher value indicates that a more intense color is required. The options range from 0 to 100.

Learn — allows you to calculate your settings based on representative color documents scanned. Before clicking Learn, place at least 5 representative color documents in the input elevator. The documents will be scanned and analyzed to determine the recommended color amount.

NOTE: The Color amount and Color threshold sliders will be updated automatically. If these values do not provide the desired results with your job set, you may need to adjust the Color threshold manually.

3-22	A-61504 April 2007

Image 39

Kodak i600 manual 3-22, A-61504 April

Contents

Page About this manual 1 IntroductionBB.tif Image outputsFB.tif FC.jpgback black and white FG.jpg2 Best Practices Scanner setup Initiate polling Error handlingEnable scanning Disable scanningBlack and white only - duplex Controlling image transfer orderColor only - duplex Dual stream - black and white and grayscale - duplex Dual stream - black and white and color - duplexPage Jam and fault recovery Image file storage locations Electronic color dropout Print string formattingContrast% = Threshold = Color Filter = Red dropout Red Dropout  Near Complete DropoutRed Dropout - Complete Dropout Blue Dropout  Near Complete Dropout Green Dropout  Complete DropoutGreen Dropout  Near Complete Dropout Blue Dropout  Complete DropoutImage header information Zone processing Patch Detect  indicates whether or not the scanner detected a togglepatch on the document side independent. If a toggle patch appears on Installation Overview Terminology and features 3 Using the TWAIN DatasourceValidation Tool Accessing the ScanValidation ool Select StartProgramsKodakDocument ImagingScanThe TWAIN interface is divided into three main sections The main Kodak Scanner window Black and White Document Black and White Document OCR QualityColor Document Color Document OCR Quality Color Photograph Two Sided scans the front and back of the document About displays the scanner’s version and copyright information Information iconsThe Image Settings window Preview area Toolbar buttonsInformation icons Page Compression - allows you to reduce your electronic image size Part of the document if you select Document Automatically Detect and StraightenAutomatically Detect or Document Manually Select Origin x, ySize W, H if you select Document Automatically Detect and Straighten none180 degrees noneLandscape 90 degreesImage Settings - Adjustments tab - Black and White Filters Noise none Filters Image noneNo Noise Filter Used Image Settings Enhancements tabThe options available on the Enhancements tab depend on the Scan as Input document is - select Two Sided, One Sided - Front, or One Advanced tabOne indicates you want the scanner to create one image Delete removes the selected image type Add adds an image type to the bottom of the configuration listToolbar buttons Change allows you to change the currently selected image typeSensitivity Content Settings tabA-61504 April 3-2210. Select Sides Both Color 24-bit 5. Select Images per side One - based on document content4. Select Input document is Two Sided select Grayscale9. Select Sides Both Color 24-bit Creating multiple images for each side of a document5. Select Images per side Multiple make sure Black and White 1-bit is selected4. Select Images per side One Creating different settings for each side of a document3. Turn on the Different settings per side option 2. Select Input document is Two SidedInformation icons The Device Settings windowDevice - General tab Paper sourceDocument Feeder A-61504 April NOTE Using this option will decrease overall throughputDiagnostics - displays the Diagnostics tab 3-28Device - Printer tab Date Format MMDDYYYY DDMMYYYY YYYYMMDD DDD Julian YYYYDDD Julian Feed Direction none Ultrasonic detectionContinue Scanning the scanner will continue to scan Patch Code Information for Kodak Document Scanners for complete Device - Patch tabCreating a new Setting Shortcut 10. Select Save As. The Save As window will be displayed 4. Select the appropriate options on the General tab6. Click Preview to review the resulting image 9. Select Home to return to the main Kodak Scanner window2. Select Settings to display the Image Settings window The Diagnostics window Diagnostics - General tabTests Scanner Time Refresh displays the scanner time3-39 A-61504 April 3. Click OK when the calibration is successfulFor changes to take effect, you must restart your application 3-40Images Logs Toolbar buttonsRefresh redisplays the log The main ISIS Driver window 4 Using the ISIS DriverMain tab Image ModeOff no patches will be used A-61504 April A-61504 April Image Orientation Layout tabGeneral options when Fixed to Transport or Relative to Document is selectedand grayscale images that is widely used by scanners, digital cameras Color optionsScanner tab Normal select when you are scanning a stack of documents ofDocument Feeder options TimeoutPower Saver Multi-feed DetectionDetect Only OperationsStop Feeder and Transport stops the feeder and the transport and Page Low documents require only a small amount of color to be saved as Color ContentLearn Dropout tab Color DropoutBlack and White or Grayscale is selected Black and White, Grayscale and Color you want to delete. The Blank Image DetectionDefining your print string Print on the front of document before scanning enables theImprinter tab ModeUnits - select Inches, Centimeters or Pixels Operator Log tabAbout tab Displays information about your scanner and driverA-61504 April A-61504 April 4-20Area Previous Location/Name Appendix A TWAIN Image Processing TerminologyFeature Camera Selections Feature Color TablesOptions Feature CroppingFeature Polarity Options