SETTING UP:
Note:
When putting the Weather Center into operation, it is important to perform in close proximity (e.g. on a table) a complete wiring and
as 1.1.05, the weather icons, and air pressure value. "- -
4. | Afterwards, the Weather Center will start receiving data from the transmitter. |
| The outdoor temperature, humidity wind chill and wind speed should then be |
| displayed on the Weather Center. If this does not happen after 30 seconds, the |
Wireless transmission at 915 MHz - thermo- hygro sensor to the Weather Center
Rain sensor
Cable connection | Cable connection |
between the rain sensor | between the wind sensor |
and the | and the |
sensor | sensor |
Weather Center
Wind sensor
1.Unwind the cables of the Rain and the Wind sensors. Connect the Rain and the Wind sensors to the
Sockets for wind 
and rain sensor
2.First insert the batteries into the
3.Then insert the batteries into the Weather Center (see “How to install and replace the batteries into the Weather Center” below). Once the batteries are installed in the Weather Center, all segments of the LCD will light up briefly and a short signal tone will be heard. It will then display the time as 12:00, the date
| batteries will need to be removed from both units. You will have to start again |
| from step 1. |
5. | You may then check all cables for correct connection and all components for |
| correct function by manually turning the |
| tilting the rain sensor to hear the impact of the internally moving seesaw, etc |
| (See Positioning below). |
6. | Time and date shall be manually set (See Manual Setting below). |
7. | After the Weather Center has been checked for correct function with regard to |
| the above points and found fit, the initial set up of the weather station system is |
| finished and the mounting of the system components can take place. It must be |
| ensured however that all components work properly together at their chosen |
| mounting or standing locations. If e.g. there appear to be problems with the 915 |
| MHz radio transmission, they can mostly be overcome by slightly changing the |
| mounting locations. |
8. | Insert the batteries into the Bonus Receiver (see “How to install and replace |
| the batteries into the Bonus Receiver” below). |
9. | Once the batteries are installed, all segments of the LCD will light up briefly. It |
| will then display the time as 12:00 and the indoor temperature. |
10. | The outdoor temperature and humidity will be display after reception of data |
| from the transmitter. If this does not happen after 1 minute, the batteries will |
| need to be removed from all the units. You will have to start again from step 1. |
| Note: Please refer to the “Bonus Receiver functions and settings” below. |
6
Note:
The radio communication between the receiver and the transmitter in the open field reaches distances of max 330 feet, provided there are no interfering obstacles such as buildings, trees, vehicles, high voltage lines, etc.
11.Radio interferences created by PC screens, radios or TV sets can in some cases entirely cut off radio communication. Please take this into consideration when choosing standing or mounting locations.
Note :
•After batteries are installed in the transmitter, install the batteries in the weather center and the bonus receiver to receive the signal from the transmitter as soon as possible. If the weather center is powered more than 5 hours after the transmitter is powered, the weather center will never receive signal successfully from this transmitter. In this case, user will need to reinstall the batteries from the transmitter to redo
•After batteries are installed, there will be synchronization between weather center and the transmitter. At this time, the signal reception icon will be blinking. When the signal is successfully received by the weather center, the icon will be switched on. (If it is not successful, the icon will not be shown in LCD) So the user can easily see whether the last reception was successful (icon on) or not (icon off). On the other hand, the short blinking of the icon shows that a reception is in progress.
9
7
Transmitter signal reception icon
•If the signal reception is not successful on the first frequency (915MHz) for 14 seconds, the frequency is changed to 920MHz and the learning is tried another 14 seconds. If still not successful the reception is tried for 14 seconds on 910MHz. This will also be done for
HOW TO INSTALL AND REPLACE THE BATTERIES INTO THE
The outdoor
1.Uninstall the rain cover of the transmitter. 2.Remover the battery compartment cover.
3.Insert the batteries, observing the correct polarity (see the marking in the battery compartment).
4.Replace the battery cover and the rain cover onto the unit.
Note:
In the event of changing batteries in any of the units, all units need to be reset by following the setting up procedures. This is because a random security code is assigned by the thermo-
10
8
hygro sensor at
HOW TO INSTALL AND REPLACE THE BATTERIES INTO THE WEATHER CENTER
The Weather Center works with 3 x AA, IEC LR6, 1.5V batteries. When the batteries need to be replaced, the low battery symbol will appear on the LCD.
To install and replace the batteries, please follow the steps below:
1. Remove the battery compartment cover.
2. Insert the batteries observing the correct polarity (see the marking in the battery compartment).
3.Replace the battery cover.
HOW TO INSTALL AND REPLACE THE BATTERIES INTO THE BONUS RECEIVER 
| Hanging hole |
LCD |
|
Display |
|
| Battery compartment |
| cover |
Function Keys | Foldout stand |
11
