Land Pride

Table of Contents

Section 1: Assembly and Set-up

!WARNING!

Be sure center deck and wings are lowered to the ground and all hydraulic pressure is relieved before disconnecting any hydraulic lines or fittings between the Rotary Cutter and tractor hydraulic system.

Refer to Figure 1-6 on page 13:

1.Route cylinder hoses (#7) through hose support loop and connect to tractor remote outlets.

2.Cycle hydraulic system by raising and lowering center deck cylinder and wing fold cylinders. It may be necessary to purge the hydraulic system of trapped air if operation is sluggish.

The system may be purged as follows:

a.With wings lowered to the ground and hydraulic pressure relieved, loosen hydraulic hose fitting at each wing cylinder slightly to allow fluid to escape.

b.Slowly activate tractor control valve to purge any trapped air from the system.

c.Tighten each fitting.

3.The center deck lift cylinder is purged in the same manner as the wing cylinders. The cutter must be resting on the ground and all hydraulic pressure relieved before loosening hose fitting as described in 2a above.

4.Check driveline for adequate clearance under all ranges of cutter height. With driveline shaft attached to the tractor, slowly raise and lower the cutter to its upper and lower limits while observing clearances between hitch and driveline. Adjust tractor drawbar height and/or length if driveline interferes. See Figure 1-1 on page 11 for correct drawbar dimensions.

Unhooking From the Cutter

1.Park cutter on a level solid hard surface. Place tractor gear selector in park and set park brake.

Refer to Figure 3-1& Figure 3-2 on page 18:

2.Raise wings up in the transport position and place transport lock bars in the locked position. Make sure transport bars are secured in place with lock

pins (#2) and hairpin cotters (#1).

Refer to Figure 2-2 on page 16:

3.Remove stroke control spacers from the center hydraulic cylinder and lower cutter until front skids are resting on the ground. Replace stroke control spacers as needed to support wheels at this position.

4.With tractor gear selector in park and park brake set, shut tractor engine off, and remove switch key. Move cylinder lift levers back and forth to release hydraulic line pressure.

Refer to Figure 1-6 on page 13:

5.Remove jack stand (#3) from the left hand wing deck and attach to cutter hitch. Secure jack stand in place with attached jack pin (#8).

6.Unhook hydraulic hoses (#7), driveline safety chains (#6), driveline (#5) and hitch safety chain (#4) from the tractor. Store hose ends in hose support loop.

7.Adjust jack stand up or down as need to remove hitch pin (#1).

8.Drive tractor away from the cutter and then lower jack stand to rest cutter on its front skid shoes.

2/02/09

RC5020 (540 RPM) and RCM5020 (1000 RPM) Rotary Cutters 318-474M

15

Page 16 Page 18
Page 17
Image 17
Land Pride RC5020, RCM5020 manual Unhooking From the Cutter, Refer to -6 on, Refer to -1& -2 on, Refer to -2 on
Page 16 Page 18

RC5020, RCM5020 specifications

The Land Pride RC5020 is a robust rotary cutter designed for agricultural and commercial applications, addressing the need for efficient vegetation management and land maintenance. This machine stands out in its class due to its exceptional durability and innovative features tailored for performance and reliability.

One of the key characteristics of the RC5020 is its heavy-duty construction. Built with a 10-gauge steel deck, it provides exceptional strength and longevity, capable of handling tough cutting conditions. The reinforced blade mounting system ensures maximum blade support, while the ΒΌ-inch thick side skirts add a layer of protection against debris and wear. This rugged structure enables users to tackle dense grass, brush, and other challenging vegetation without compromising performance.

The RC5020 is equipped with a powerful drive system that employs a smooth-running gearbox, ensuring efficient power transmission from the tractor to the cutter. This technology allows for a consistent performance and superior cutting ability, reducing downtime and maintenance needs. The machine features a quick-change blade system, enabling operators to easily replace blades when necessary, further enhancing productivity.

Versatility is another hallmark of the RC5020, as it can be operated with various tractor sizes, making it an excellent choice for both small farms and larger agricultural operations. With a cutting width of 20 feet, it efficiently covers large areas, minimizing the time needed for mowing and land clearing. The cutter also boasts an adjustable cutting height, allowing users to set the machine to their specific requirements, whether it be trimming grasses or cutting back invasive brush.

Safety features are integrated into the design of the RC5020, ensuring operator protection. These include a heavy-duty chain guard that minimizes the risk of flying debris and a unique safety latch designed to keep the cutter securely closed during transport. Additionally, the easy-access maintenance points make routine inspections and servicing quick and straightforward.

In summary, the Land Pride RC5020 rotary cutter combines robust construction with advanced technology, making it an essential tool for anyone needing effective land management. Its versatility, efficient performance, and safety features make it an ideal choice for agricultural professionals and property owners alike. Whether for mowing grass or clearing larger brush areas, the RC5020 proves to be a reliable and powerful ally in maintaining landscapes with ease and efficiency.
Top Page Image Contents