Land Pride

Table of Contents

Section 3: Operating Instructions

Field Set-up

!WARNING!

The following operational procedures should be carried out by the tractor operator. Other persons should be cleared of the area even during cutter set-up. Cutter operation should be stopped when in the vicinity of other persons.

Refer to Figure 3-3:

1.Inspect wing blade carriers and cutting blades prior to lowering the wings.

NOTE: The cutting blades may become locked together (overlapped) when wings are raised to transport position. Operating the cutter under such circumstances will result in severe deck vibration. Inspect wing decks for a locked blade condition prior to power-on operation. Use a pry bar or other tool to separate cutting blades when necessary.

Blade Carrier

Wing Deck

Cutting Blades

24854

Wing Deck Blade Positioning

Figure 3-3

Refer to Figure 3-1& Figure 3-2on page 18:

2.Raise both wings up to release any tension on the transport lock bar as shown in Figure 3-1.Remove hairpin cotter (#1) from both the left and right cylinder pins (#4).

3.Rotate end of transport lock bar (#3) to the storage pin (#2) as shown in Figure 3-2.Secure with hairpin cotters (#1).

4.Lower both left and right wing sections down.

5.Extend hydraulic lift cylinder to release any pressure against the stroke control spacers. Remove stroke control spacers. Keep spacers with tractor for field installation.

6.Increase throttle to approximately 1/4 engine speed and slowly engage driveline. Also see note below.

NOTE: Use tractor’s PTO soft start option if available.

7.Ensure that all power shafts are rotating and that the cutter has no vibration.

8.Continue to increase throttle to full 540 or 1000 PTO speed before commencing forward operation.

9.While cutting, use the lever for the hydraulic lift cylinder to set the cutter to correct cutting height.

10.Once cutting height has been set, stop traveling, disengage driveline, shut tractor engine off and remove switch key. Do not change lift cylinder stroke length.

11.Install stroke control spacers onto the lift cylinder rod until the rod is filled between the cylinder and clevis. Always install the largest spacers first and the smaller ones last. If necessary, raise cutter slightly to install the last spacer.

12.Return to the tractor and bring cutter up to full rpm as outlined in steps 7, 8 & 9 and then continuing cutting operation.

Operating Speed

Refer to Figure 3-4& Figure 3-5:

Optimum ground speed depends on density of material being cut, horsepower rating of the tractor and (in some cases) terrain. Always operate tractor at cutter’s full rated PTO speed in a gear range that allows the cutter to make a smooth cut without lugging the tractor down, usually between 2 to 5 mph. Low PTO speed will allow the blades to hinge back resulting in a ragged uneven cutting.

Wing Operating Angle

Use the float position of your tractor’s hydraulic system to provide automatic floating of the wings for varying terrain conditions. This will ensure that the wing gauge wheels are in continuous contact with the ground at all times.

IMPORTANT: Do not operate this cutter under any terrain conditions where, on a continuous cut, the wing angle exceeds 45 degrees up. Damage to the wing driveline and gearboxes can occur.

IMPORTANT: During operation, the wing lift lever(s) must be in the float position to avoid damage to the cylinders and axles.

2/02/09

RC5020 (540 RPM) and RCM5020 (1000 RPM) Rotary Cutters 318-474M

19

Page 20 Page 22
Page 21
Image 21
Land Pride RC5020, RCM5020 Field Set-up, Operating Speed, Wing Operating Angle, Refer to -1& -2on, Refer to -4& Figure
Page 20 Page 22

RC5020, RCM5020 specifications

The Land Pride RC5020 is a robust rotary cutter designed for agricultural and commercial applications, addressing the need for efficient vegetation management and land maintenance. This machine stands out in its class due to its exceptional durability and innovative features tailored for performance and reliability.

One of the key characteristics of the RC5020 is its heavy-duty construction. Built with a 10-gauge steel deck, it provides exceptional strength and longevity, capable of handling tough cutting conditions. The reinforced blade mounting system ensures maximum blade support, while the ΒΌ-inch thick side skirts add a layer of protection against debris and wear. This rugged structure enables users to tackle dense grass, brush, and other challenging vegetation without compromising performance.

The RC5020 is equipped with a powerful drive system that employs a smooth-running gearbox, ensuring efficient power transmission from the tractor to the cutter. This technology allows for a consistent performance and superior cutting ability, reducing downtime and maintenance needs. The machine features a quick-change blade system, enabling operators to easily replace blades when necessary, further enhancing productivity.

Versatility is another hallmark of the RC5020, as it can be operated with various tractor sizes, making it an excellent choice for both small farms and larger agricultural operations. With a cutting width of 20 feet, it efficiently covers large areas, minimizing the time needed for mowing and land clearing. The cutter also boasts an adjustable cutting height, allowing users to set the machine to their specific requirements, whether it be trimming grasses or cutting back invasive brush.

Safety features are integrated into the design of the RC5020, ensuring operator protection. These include a heavy-duty chain guard that minimizes the risk of flying debris and a unique safety latch designed to keep the cutter securely closed during transport. Additionally, the easy-access maintenance points make routine inspections and servicing quick and straightforward.

In summary, the Land Pride RC5020 rotary cutter combines robust construction with advanced technology, making it an essential tool for anyone needing effective land management. Its versatility, efficient performance, and safety features make it an ideal choice for agricultural professionals and property owners alike. Whether for mowing grass or clearing larger brush areas, the RC5020 proves to be a reliable and powerful ally in maintaining landscapes with ease and efficiency.
Top Page Image Contents