Manuals / Land Pride / Lawn and Garden / Brush Cutter

Land Pride RCR1572 Lubrication Points, Hours, Gauge Wheel Spindle Tube, Gauge Wheel Hub, Gearbox

Models: RCR1548 RCR1542 RCR1572 RCR1560

1 28

Download 28 pages 32.13 Kb

Page 21

Lubrication Points

Land Pride

Table of Contents

Section 4: Maintenance and Lubrication

Lubrication Points

Lubrication Legend

	Multi-purpose	Multi-purpose	Multi-purpose	50
	spray lube	grease lube	oil lube

Intervals in hours at which lubrication is required

16344

24

Hours

Gauge Wheel Spindle Tube

Type of Lubrication: Grease

Quantity = 6 pumps

16278

8

Hours

Gauge Wheel Hub

The gauge wheel hub is equipped with a relief hole located directly opposite the grease fitting. The relief hole releases pressure from inside the hub casting when it is greased. The hub should be greased until grease purges from the relief hole.

Type of Lubrication: Multipurpose Grease

Quantity = Until grease purges from the relief hole

16345

8

Hours

Gearbox

Check oil level in the gearbox by removing the side plug in the gearbox case. If the oil level is low, remove the top plug in the gearbox case and fill with EP90 oil until oil flows from the side port of gearbox case. Reinstall plugs and tighten.

NOTE: Do not overfill! Cutter should be level when checking oil.

ype of Lubrication: EP90 Oil

Quantity = fill until oil flows from the side port of gearbox case.

12/28/05

RCR1542, RCR1548, RCR1560 and RCR1572 Rotary Cutters 312-556M

19

Image 21

Land Pride RCR1572 manual Lubrication Points, Hours, Gauge Wheel Spindle Tube, Gauge Wheel Hub, Gearbox, Table of Contents

Contents

RCR1542, RCR1548, RCR1560 and RCR1572 Table of ContentsOperator’s Manual you see this symbol, the subsequentImportant Safety Information Table of ContentsSection 1 Assembly and Set-Up Section 4 Maintenance and LubricationLook For The Safety Alert Symbol Safety at All TimesImportant Safety Information Be Aware of Signal WordsUse A Safety Chain Use Safety Lights and DevicesPractice Safe Maintenance Transport Machinery SafelyWear Protective Equipment Prepare for EmergenciesKeep Riders Off Machinery Avoid High Pressure Fluids Hazard818-540C Safety LabelsTable of Contents Important Safety Information818-556C 818-552C818-564C 818-142CImportant Safety Information Table of ContentsLand Pride 12/28/05Land Pride Service Department Using This ManualApplication Owner AssistanceSection 1 Assembly and Set-Up Dealer AssemblyTractor Requirements Refer to FigureDriveline Installation Table of ContentsDANGER 3-Point Hook-UpTable of Contents PTO HookupSection 1 Assembly and Set-Up Refer to FigureVent Plug Oil Plug DO NOT OVERFILL Vent Plug InstallationTable of Contents Section 1 Assembly and Set-UpSection 2 Options Safety GuardsRubber Guards RCR1542 & RCR1548 Front Rubber Guard RCR1560 & RCR1572Rear Chain Guard RCR1560 & RCR1572 Front Chain Guard RCR1560 & RCR1572Table of Contents Section 2 OptionsTransporting Operating ChecklistOperating Check List Cutting InstructionsNominal Cutting Height Leveling ProcedureTable of Contents DANGERTable of Contents Cutter Height Adjustment3-PointCutter Height Adjustment Figure Section 3 Operating InstructionsSection 4 Maintenance and Lubrication MaintenanceService Cutting Blades Driveline ProtectionClutch Assembly Clutch DisassemblyStorage InspectionHours Lubrication PointsGauge Wheel Spindle Tube Gauge Wheel HubDriveline Shield Bearings Driveline U-JointsDriveline Profiles Table of ContentsRCR15 Series Rotary Cutters Section 5 Speciﬁcations & CapacitiesRCR1542 RCR1548Features Section 6 Features and BeneﬁtsRCR15 Series Single Deck Rotary Cutters BenefitsProblem Section 7 TroubleshootingSolution CauseSection 8 Appendix Torque Values Chartin-tpi ft-lbWarranty Table of ContentsSection 8 Appendix Corporate Ofﬁce P.O. Box