Land Pride | Table of Contents |
Section 7: Troubleshooting
Problem | Cause | Solution | |
Oil seal leaking | Gearbox overfilled | Drain to side plug hole | |
|
|
| |
| Seals damaged | Replace seals | |
|
|
| |
| Grass or wire wrapped on | check seal areas daily | |
| shaft in seal area |
| |
|
|
| |
Driveline yoke or cross failing | Shock load | Avoid hitting solid objects | |
|
|
| |
| Needs lubrication | Lubricate every 8 hours | |
|
|
| |
Driveline | Scalping the ground | Raise cutting height | |
clutch slipping |
|
| |
|
|
| |
| Cutting too fast | Reduce travel speed | |
|
|
| |
| PTO being engaged too | Slowly engage PTO at low engine rpm | |
| fast at high engine rpm |
| |
|
|
| |
| Cutting over solid objects | Avoid solid objects | |
|
|
| |
Bent Driveline (NOTE: driveline should | Contacting frame | Reduce lift height in transport position | |
be repaired or replaced if bent) |
|
| |
Contacting drawbar | Reposition drawbar | ||
| |||
|
|
| |
| Bottoming out | Shorten driveline | |
|
|
| |
Driveline | Shock load | Avoid hitting solid objects | |
telescoping tube failing |
|
| |
|
|
| |
Driveline | Needs lubrication | Lubricate every 20 hours | |
telescoping tube wearing |
|
| |
|
|
| |
Blades wearing excessively | Cutting on | Raise cutting height | |
| sandy ground |
| |
|
|
| |
| Contacting | Raise cutting height | |
| ground frequently |
| |
|
|
| |
Blades breaking | Hitting solid objects | Avoid hitting solid objects | |
|
|
| |
| Blades hitting each other | Blade carriers need to be timed | |
|
|
| |
Blades coming loose | Blades not | Tighten blade hardware (refer to | |
| tightened properly | "Servicing Cutter Blades" on page 17 | |
|
|
| |
| Improper deck attitude | Lower front of deck, see page 14 | |
|
|
| |
Blade carrier becomes loose | Running loose in the past | Replace gearbox output shaft and blade carrier | |
|
|
| |
| Blade carrier hardware not | Tighten to specified torque | |
| tight enough |
| |
|
|
| |
Blade bolt holes worn | Blade hardware running loose | Replace blades and blade bolts if worn | |
|
|
| |
Blade carrier bent | Hitting solid objects | Avoid hitting solid objects and replace blade | |
|
| carrier | |
|
|
| |
Excessive side skid wear | Cutting height not level | Adjust cutter height | |
|
|
| |
| Soil abrasive | Adjust cutter height | |
|
|
| |
| Cutting too low | Adjust cutter height | |
|
|
| |
Tail wheel support failing | Lowering too fast | Adjust rate of drop | |
|
|
| |
| Hitting objects when turning | Reduce speed on turns | |
|
|
| |
Excessive vibration | Driveline bent | Replace driveline | |
|
|
| |
| Blades loose | Tighten blade bolts | |
|
|
| |
| Blade carrier bent | Replace blade carrier | |
|
|
| |
| Blade broken | Replace blade | |
|
|
| |
| Blade will not swing | Remove and inspect blade | |
|
|
| |
| Blades have unequal weight | Replace both blades | |
|
|
| |
|
|
|
12/28/05 | RCR1542, RCR1548, RCR1560 and RCR1572 Rotary Cutters | 23 |
