Operations, Using the Touch Screen, Tons can be

Operations	EN

Using the Touch Screen

Use only fingers to use the touch screen.

Do not allow the touch screen to come into contact with other elec-

itrical devices.

Electrostatic discharges can cause the touch screen to malfunction. Do not allow the touch screen to contact water. The touch screen may malfunction in humid conditions or when exposed to water.

To avoid damaging the touch screen, do not tap it with anything sharp or do not apply excessive pressure to it with your fingertips.

Tapping

Tap on the display to open an on- screen button or to make a selection. Tapping on the icon in the middle of the bottom line activates the distance measurement or triggers the camera.

Dragging

Drag on the display to move to prior or to next screen in the galerie function.

Pinching	Instead of using
i	the touch
i	screen, the nor-
	mal keypad but-
	tons can be
	used also.

Spread 2 fingers apart to zoom if pointfinder is activated.

Leica DISTOTM D810 touch 799093a	6

Page 7

Image 7

Leica 806648, DISTO D810 manual Operations, Using the Touch Screen, Tons can be, Used also

Contents

Original laser distance meter Leica Distotm D810 touch Leica Distotm Table of Contents Introduction Instrument Set-upOverview Status bar Main line Function SettingsBasic measuring screen Selection screen Crosshair Zoom with navi- gation keys up and down Pointfinder ViewscreenZoom stage Active function Favorites Charge batteries when battery symbol is flashing Charging the Li-Ion battery via USB Tons can be Using the Touch ScreenOperations Touch Undo last action Switching ON/OFF ClearMultifunctional endpiece Permanent / Minimum-Maximum measuring Add / Subtract Areas or volumesNext meas- urement is added to the previous one Screenshot photo is saved in gallery Screenshot Tilt units Settings Following Switch betweenDistance units Art. No US-Model Art. No Beep ON/OFF De-/Activate keylock Switch on with keylockDigital level ON/OFF Bluetooth Settings Basic Calibration of tilt sensor Tilt CalibrationAfter 2 sec Device Illumination Personalized favoritesTouch Screen ON/OFF Set time hhmm Compass AdjustmentSet date yyyy-mm-dd Exit settings Date and Time An offset adds or subtracts a ResetIzed settings and memories are lost Offset ON/Measure TimerFunctions Starts if Reference Adjusting measuring reference/tripodCalculator If device is Target surfaces Smart Horizontal ModeMemory Measuring single distance Area Level 32.653 m Volume OV = Overview PhotoTake photo Exit For screenshots, press camera key for 2 sec Compass Measurement After switching On the deviceCompass If the device is connected to Gallery Function is active Long range modeTriangular area Time is increased Lowing point Height-profile measurementAim at reference point REF Aim at additional points Device Roof, height of chimneys,… Sloped objects Stops height Height trackingAim laser at lower point Turned on tripod Trapezium area TrapeziumAim laser at upper point Aim laser at 2nd point Use Up/Down navigation keys to show more re- sults 78.383 m Stake out Adjust digitTwo different Horizontal measuring Pythagoras 2-pointResult is shown in the main line Ment Aim laser at first target Pythagoras 3-point23.018 m 20.571 m Aiming WidthIf necessary, use Zoom for precise Round object DiameterAim laser perpendicular To the middle Length Area from PhotoSelect arrows with If necessary, use Zoom for precise With softkeys. Corre Aiming Confirm Tilt measurements a transverse tilt should be avoided Technical Data Message Codes Care Warranty Limits of use Safety InstructionsAreas of responsibility Prohibited use This device may not cause interference DisposalElectromagnetic Compatibility EMC FCC statement applicable in U.S Normativa FCC aplicable en EE UU Déclaration FCC, applicable aux Etats-Unis Laser classification Use of the product with Blue- toothLabelling

Operations

Using the Touch Screen

Tapping

Pinching

the touch

tons can be

used also.