Lennox Hearth GV230

WARNING: BE ABSOLUTELY SURE THE DISTANCE BETWEEN THE

HEATER AND THE SURFACE OF ANY COMBUSTIBLE CONSTRUC-

TION IS NOT LESS THAN SHOWN IN THE FIGURES ON PAGE 7.

Floor Protection

USA - The ﬂoor in front and under the heater must be protected with

noncombustible material. The covering must extend 16” in front of the

door opening of the heater and 8” to either side of the door opening.

Canada - The ﬂoor in front and under the heater must be protected with

noncombustible material. The covering must extend 457 mm in front of

the door opening of the heater and 200 mm to either side of the stove

body and 200 mm to the rear or to the wall, whichever is smaller.

USA and Canada - A chimney connector / venting extends horizontally

over the ﬂoor, protection must also cover the ﬂoor under the connector

/ venting and at least 2” (51 mm) to either side.

Alcove Installations USA and Canada - The ﬂoor protection must be a

thermally rated non-combustible ﬂoor protector. See Page 8 for details

on determining acceptable ﬂoor protection materials or hearth pads for

alcove installations.

Alcove Installation

Clearances - In alcove installations, only 6” double wall connector pipe

can be used (single wall or single wall pipe with shield is not allowed).

Minimum alcove width between combustible materials is 52” (1321 mm).

Maximum alcove depth is 48” (1219 mm). Minimum alcove height is

90” (2286 mm).

Thermal Floor Protection - Thermal ﬂoor protection is only required

where the stove is installed into an alcove.

Chimney and Connector

Minimum 6" diameter, minimum 24 MSG black steel connector pipe with

UL103HT listed factory-built chimney suitable for use with solid fuels

or masonry chimney. Horizontal connection not tested, refer to local

building codes for installation. See installation instructions for details.

Restrictions apply! Read instructions before installing.

Residential chimney systems must be from the same brands as listed

for mobile homes but connector pipe may be double wall, single wall, or

single wall with shield as listed.

This appliance may be vented into a code-approved masonry chimney

with ﬂue liner.

WARNING: CHIMNEY CONNECTOR MUST BE IN GOOD CONDITION AND

KEPT CLEAN. DO NOT INSTALL DAMAGED PARTS.

All of the stove connector pipe used must be of the same brand. The

chimney that the stove pipe transitions into may be a different brand.

Other than the transition of the stove pipe into the chimney, do Not mix

different brand vent components. Install all vent components per vent

manufacturer’s instructions.

The chimney connector shall not pass through an attic or roof space,

closet or similar concealed space, or a ﬂoor, or ceiling. Where passage

through a wall, or partition of combustible construction is desired, the

installation shall conform to CAN/CSA-B365, Installation Code for Solid-

Fuel-Burning Appliances and Equipment.

There must be an effective vapor barrier at the location where the chimney

or other component penetrates to the exterior of the structure. Follow the

vent manufacturer's detailed instructions.

IMPORTANT NOTE: See Draft Requirements and Selecting a Proper

Venting System on Page 4 to assist you in choosing the proper venting

system for your installation.

Clearance dimensions are to ﬂue collar. If a single wall connector pipe

with shield is used, a 1 inch air space is needed between pipe and shield.

Shield attaches to rear of stove pipe and must run from stove top to ceil-

ing. Pipe shield shall be UL listed.

Components Required For Installations

Legs OR Pedestal Assembly.

Use all required components speciﬁed for this appliance. Do

not substitute.

WARNING: In the event that you remove the blower for any

reason, make sure a cover plate (available from Lennox Hearth

Products) is installed before using the heater. Note: The cover

plate is not necessary if a blower has never been installed

because a knock-out will be in place to act as the cover.

CLEARANCES TO COMBUSTIBLES