Or Ceiling, For Canada Only | Lennox Hearth RDI-42-H, HCI-42-H

CHIMNEY 30° OFFSET THROUGH FLOOR

OR CEILING

It may be necessary to assemble the chimney at 30° when passing through the floor or ceiling area. Use the F8FS30-2 firestop spacer as shown in Figures 22 and 23. Support the chimney at floor or ceiling penetration with a FTF8 stabilizer if distance of chimney below ceiling is 10' or more. Maintain 2" minimum air space to combustibles from chimney sections.

	Attic Space
	F8FS30-2	2" Min.
	Firestop Spacer	2" Min.
		Air Space
	2" Min.	FTF8-S4 Stabilizer
	Air Space
	10'
	Max.	30° Firestop
		And Attic Above
	Figure 22
	Room Above
	F8FS30-2	2" Min.
	Firestop Spacer	2" Min.
		Air Space
	2" Min.	FTF8-S4 Stabilizer
	Air Space	FTF8-S4 Stabilizer
	Air Space
	10'	30° Firestop
	Max.	And Room Above

Figure 23

For Canada Only

When installing the chimney system through an open attic space, the attic shield assembly- firestop spacer must be used (Figure 24 ). This installation is required only for use in Canada.

Open Attic Space

Figure 24

Note: For Canadian installations, all chimney installedoutsidethebuildingmustbeconstructed with galvalume (outer sections only) effective January 1, 1992. The appropriate model desig- nations are located in the back of this manual.

Step 4. Note: Chimney sections are con- structed with a unique locking tab design, which ensures an immediate, tight assembly between sections. Plan your chimney require- ments carefully before assembly as chimney is difficult to disassemble after installation. If disassembled, the tabs might become dam- aged. Be certain tabs are properly formed to ensure locking tabs engage properly.

The Security FTF8 chimney system is a two piece chimney, which snap together from the fireplace up. Start with the inner flue section with the lanced end up, snap lock it in to the matching collar on top of the fireplace. At all subsequent joints, the upper flue section fits into the preceding flue section. Each piece snaps together by means of locking tabs (9 locking tabs per joint). Check each piece by pulling up slightly from the top to ensure proper engagement before installing the next section. If the flue has been installed correctly, it will not separate when you test it. Also, the inner flue joint where each section is joined should be tight and flat without gaps (Figure 25 ).

Figure 25

Outer pipe section installs in just the opposite way; the lanced end goes down and each new section goes OVER the outside of the previous section installed (Figure 26 ).

Locking Tabs (Lances)

Figure 26

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

Note: Assemble one component of chimney at a time (inner section first, then outer section last) before proceeding with the next complete section.

Continue to assemble the chimney up through framed opening. Assemble just enough to pen- etrate the roof flashing openings (Figure 27 ). Always maintain 2" minimum air space to com- bustible materials and always check each chim- ney joint (inner and outer) to ensure proper engagement. Check vertical alignment of chim- ney so that it projects from the roof in true vertical position.

1"* Min. Air Space To Combustibles

Figure 27

Security's chimney sections do not need to be screwed together. Additional reinforcement is not necessary except in certain offset condi- tions (refer to page 14, Figure 38 ).

Step 5. The height of vertical chimney pipe supported only by the fireplace must not ex- ceed 30'. Chimney heights above 30' must be supported by a Model FTF8-S4 stabilizer in- stalled at 30' intervals.

Note: The Model FTF8-S4 adds 3" net effective height to the total chimney system.

Install the Model FTF8-S4 stabilizer by fitting inner section down into respective section of proceeding flue pipe and locking outer stabi- lizer section into place over the outer chimney pipe. Position for proper clearance through framed opening and nail straps securely (under tension in “shear”) into place on framing. Use 8d nails. Attach successive lengths of chimney pipe directly to stabilizer using same tech- niques as described in Step 4 (Figure 28 ).

FTF8-S4 Stabilizer

Figure 28

RDI-42-H, HCI-42-H, RDI-42, HCI-42 specifications

The Lennox Hearth series includes some of the most impressive gas fireplaces available, such as the HCI-42, RDI-42-H, HCI-42-H, and RDI-42. These models are designed to blend efficiency, style, and comfort, making them ideal for modern homes.

One of the standout features of these fireplaces is their versatile design. They come in various sizes to fit a range of spaces while offering customization options that allow homeowners to tailor their aesthetic, including various trim finishes and decorative options. The HCI-42 and RDI-42-H models are particularly noted for their seamless integration into both traditional and contemporary home decor.

The technology behind Lennox Hearth fireplaces ensures high performance and efficiency. Utilizing advanced burner technology, these models provide realistic flame patterns and a beautiful glowing ember bed, creating a captivating visual experience. The direct vent system allows for efficient heating while minimizing heat loss, making these fireplaces ideal for energy-conscious consumers. With a focus on environmentally friendly operation, these units produce fewer emissions compared to traditional wood-burning fireplaces.

User convenience is also a top priority with Lennox Hearth. Many models feature remote control functionality, allowing users to adjust heat and flame settings effortlessly. The easy-to-use thermostatic controls enable homeowners to maintain their desired comfort level without the hassle of manual adjustments. Additionally, the lightweight construction and simplified installation process make it easier for homeowners and contractors alike to set up these fireplaces.

Safety features are integral to Lennox Hearth products. These include sealed combustion systems that prevent outdoor air from entering the home and built-in safety shut-off systems to ensure peace of mind. The HCI-42 and its counterparts have been rigorously tested for safety and performance, adhering to strict industry standards.

In summary, the Lennox Hearth HCI-42, RDI-42-H, HCI-42-H, and RDI-42 bring together cutting-edge technology, beautiful design, and ease of use to offer homeowners a top-tier fireplace experience. With their efficient heating capabilities, customizable aesthetics, and emphasis on safety, these models stand out as exceptional choices for modern living spaces. Whether you are looking to enhance your home’s ambiance or increase energy efficiency, Lennox Hearth fireplaces are a smart investment for any homeowner.

Lennox Hearth RDI-42-H, HCI-42 Or Ceiling, For Canada Only, Open Attic Space, FTF8-S4 Stabilizer

Models: RDI-42-H HCI-42-H RDI-42 HCI-42

OR CEILING

For Canada Only

Open Attic Space

FTF8-S4 Stabilizer

RDI-42-H, HCI-42-H, RDI-42, HCI-42 specifications