REFRIGERATOR INSTALLATION

WARNING

Excessive Weight Hazard Use two or more people to move and install

refrigerator.

Failure to do so can result in back or other injury.

3.Install this appliance in an area where the temperature is between 55°F (13°C) and 110°F (43°C.) If the temperature around the appliance is too low or high, cooling ability may be adversely affected.

CAUTION: Avoid placing the unit near heat sources, direct sunlight or moisture.

UNPACKING YOUR REFRIGERATOR

Remove tape and any temporary labels from your refrigerator before using. Do not remove any warning- type labels, the model and serial number label, or the TechSheet that is attached to back wall of the refrigerator.

To remove any remaining tape or glue, rub the area briskly with your thumb. Tape or glue residue can also be easily removed by rubbing a small amount of liquid dish soap over the adhesive with your fingers. Wipe with warm water and dry.

Do not use sharp instruments, rubbing alcohol, flammable fluids or abrasive cleaners to remove tape or glue. These products can damage the surface of your refrigerator. For more information, see the Important Safety Instructions section.

Refrigerator shelves are installed in the shipping position.

Please reinstall shelves according to your individual storage needs.

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator for cleaning or service, be sure to protect the floor. Always pull the refrigerator straight out when moving it. Do not wiggle or walk the refrigerator when trying to move it, as floor damage could occur.

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from refrigerator.

Failure to do so can result in death, explosion or fire.

INSTALLATION

1.Avoid placing the unit near heat sources, direct sunlight, or moisture.

2.To avoid vibration, the unit must be level. If required, adjust the leveling screws to compensate for unevenness of the floor. The front should be slightly higher than the rear to aid in door closing. Leveling screws can be turned easily by tipping the cabinet

slightly. Turn the leveling screws clockwise ( ) to

raise the unit, counterclockwise () to lower it.

NEXT

1.Clean your refrigerator thoroughly and wipe off all dust accumulated during shipping.

2.Install accessories such as ice cube bin, drawers, shelves, etc., in their proper places. They are packed together to prevent possible damage during shipment.

3.Let your refrigerator run for 2 or 3 hours before putting food in it. Check the flow of cold air in the freezer compartment to ensure proper cooling. Your refrigerator is now ready for use.

WARNING:

Be careful when you work with hinge, base grille, stopper etc. You may be injured.

Do not put hands or metal sticks into air vents, base grille or bottom of refrigerator. You may be injured or receive an electrical shock.

BASE GRILLE

To remove the base grille:

1.Grasp the grille with both hands.

2.Pull the grille toward yourself.

To install the base grille:

1.Place clips in openings in the metal panel.

2.Push the grille toward the refrigerator until it snaps into place.

A proper distance from adjacent items

Please keep the refrigerator at a proper distance from other things. Too small a distance from adjacent items may result in lowered freezing capability and increased electricity consumption charges.

(2.54 cm) 1”

10

Page 10
Image 10
LG Electronics LDC2272, LRBC2051, LBC2252 Refrigerator Installation, Unpacking Your Refrigerator, Next, Base Grille

LBC2252, LDC2272, LRBC2051 specifications

LG Electronics has established itself as a leader in the home appliance sector, known for its innovative technology and commitment to quality. The LG LRBC2051, LDC2272, and LBC2252 are three notable models that exemplify the brand's dedication to efficiency and modern design, catering to a variety of consumer needs.

Starting with the LG LRBC2051, this refrigerator is designed for optimal freshness and convenience. One of its standout features is the Smart Inverter Compressor, which intelligently adjusts cooling performance based on the amount of food stored, resulting in energy savings and reduced noise levels. The multi-air flow system ensures even cooling throughout the refrigerator, preventing hot spots and promoting the longevity of food. Additionally, the LRBC2051 boasts a sleek design with a fingerprint-resistant finish, making it both functional and aesthetically pleasing for any kitchen.

Next, the LDC2272 model takes innovation a step further with its Door-in-Door design, allowing easy access to frequently used items without exposing the entire refrigerator compartment. This feature minimizes cold air loss and enhances energy efficiency. The LDC2272 also includes a Smart Diagnosis feature, which helps users solve issues quickly via a smartphone app, reducing service call costs. Combined with a spacious interior and adjustable shelving, this model balances style and practicality seamlessly.

Lastly, the LG LBC2252 refrigerator is ideal for families, offering a robust storage capacity and versatile organization options. It features a sleek, modern look with LED lighting that illuminates the interior, making it easy to find items at a glance. The water and ice dispenser is another highlight, providing convenient access to refreshing drinks while maintaining the cleanliness of the fridge's interior. The smart cooling system actively monitors and maintains optimal humidity levels, ensuring perishables stay fresher for longer.

In summary, LG Electronics has made significant strides in refrigerator technology with models like the LRBC2051, LDC2272, and LBC2252. Equipped with advanced features like Smart Inverter Compressor, Door-in-Door design, and smart cooling systems, these refrigerators demonstrate LG's commitment to enhancing the user experience, promoting energy efficiency, and preserving food freshness. Each model caters to specific consumer needs, making them excellent choices for modern kitchens.