ASSEMBLING THE
UPRIGHT EXERCISE BIKE
Tools Required: Metric Wrench Set, Metric Allen
Wrench Set, Phillips Screwdriver
1. Locate and install the two LEVELER FEET (A) to the bottom of
the REAR STABILIZER (B).
2. With the bends facing rearward, attach the REAR STABILIZER
(B) to the BASE UNIT (C) using two 2-3/8" BUTTON HEAD
SCREWS (1) from the top of the REAR STABILIZER BRACKET
(D) and two 13/16" BUTTON HEAD SCREWS (2) from the front
side of the REAR STABILIZER BRACKET. Tighten the
SCREWS securely.
3. Locate the MONOCOLUMN (E). Cut the WIRE TIE securing the
WIRE (F) to the bottom of the MONOCOLUMN. Slide the
MONOCOLUMN COVER (G) onto the MONOCOLUMN (E) as
shown. Slide the MONOCOLUMN COVER up to the HANDLE-
BAR TUBE (H).
5. Locate and insert the GROMMET (J) into the SIDE ACCESS
HOLE (K) of the MONOCOLUMN (E). Pull the WIRE (F) out
through the SIDE ACCESS HOLE.
6. With the HANDLEBAR TUBE (L) facing the rear of the unit as
shown, slide the MONOCOLUMN (E) into the MONOCOLUMN
BRACKET(M) of the BASE UNIT (C) . Slide the MONOCOL-
UMN down until it is fully seated. Secure the MONOCOLUMN to
the MONOCOLUMN BRACKET using two 3-15/16" HEX HEAD
BOLTS (3) and three THICK FLATWASHERS (4) (as shown)
from the rear side of the MONOCOLUMN and two 2-3/8" HEX
HEAD BOLTS (5) and THICK FLATWASHERS (4) from the
user left side of the MONOCOLUMN BRACKET. Tighten the
BOLTS securely.
CAUTION: Be careful not to pinch the WIRE(S) (N) leading
from the MONOCOLUMN BRACKET (M) when inserting the
MONOCOLUMN (E) into the MONOCOLUMN BRACKET.
7. Connect the WIRE(s) (N) leading from the MONOCOLUMN
BRACKET(M) to the corresponding WIRE (F) from the SIDE
ACCESS HOLE (K) of the MONOCOLUMN (E). Slide the
MONOCOLUMN COVER (G) downward to the meet the MAIN
SHROUDS (O). Secure the MONOCOLUMN COVER to the
MAIN SHROUDS using four 1/2" PHILLIPS SCREWS (6) and
matching FLATWASHERS (7). Tighten the SCREWS securely.
Do not overtighten the SCREWS.
8. Locate the SEAT(P) and SEATPOST (Q). Remove the three
NYLOCK NUTS (8) and FLAT WASHERS(9) from the threaded
studs on the bottom of the SEAT. Align the three threaded studs
of the SEATwith the mounting holes in the SEAT POST
MOUNTING PLATE (R). Secure the SEAT to the SEATPOST
MOUNTING PLATE using the three previously removed
NYLOCK NUTS and FLATWASHERS. Tighten the NUTS
securely.
9. Locate the SEATPOST CAP (S). With the curved side facing
upward toward the SEAT(P) and the inside notch aligned with
the SEATPOST ADJUSTMENT DECAL, slide the SEATPOST
CAPover the SEATPOST (Q).
10. Locate and slide the SEAT POST SPACER (T) over the end of
the SEATPOST (Q). Using two 1/4" PHILLIPS SCREWS (10),
secure the SEATPOST SPACER to the end of the SEATPOST.
Tighten the SCREWS securely.
11. With the nose of the SEAT (P) facing forward, insert the SEAT
POST(Q) into the SEAT POST SUPPORT(U).
12. Slide the SEATPOST CAP (S) downward to meet the top of the
SEATPOST SUPPORT (U). Secure the SEAT POST CAP to the
SEATPOST SUPPORT using two 1/4" PHILLIPS SCREWS
(11). Tighten the SCREWS securely. Do not overtighten the
SCREWS.
13. Begin inserting the SEATADJUSTMENT KNOB (V). Lift upward
on the SEAT(P) and SEATPOST (Q) until the SEATPOST
locks into a position. Tighten the SEATADJUSTMENT KNOB
fully. Insert the 1/4" PHILLIPS LOCKING SCREW (12) and tight-
en securely.
14. Locate the ACCESSORYTRAY (W). Position the ACCESSORY
TRAYnear the top of the MONOCOLUMN (E) at the DISPLAY
CONSOLE BRACKET (X). While holding the CONNECTOR (Y),
cut the wire tie securing the CONNECTOR to the DISPLAY
CONSOLE BRACKET. Feed the WIRE(s) (Z) leading from the
TOPACCESS HOLE (AA) of the DISPLAYCONSOLE BRACK-
ETthrough the center hole of the ACCESSORY TRAY MOUNT-
ING BRACKET (BB). Secure the ACCESSORY TRAYto the
DISPLAYCONSOLE BRACKET using two 5/8" BUTTON HEAD
SCREWS (13) and matching FLAT WASHERS (14). Tighten the
SCREWS securely.
CAUTION: Be careful not to pinch the WIRE(S) (Z) leading
from the DISPLAYCONSOLE BRACKET (X) when securing
the ACCESSORYTRAY (W) to the DISPLAYCONSOLE
BRACKET.
NOTE: Be careful not to let the CONNECTOR (Y) fall into the
DISLAYCONSOLE BRACKET (X).
15. Remove the DISPLAYCONSOLE (CC) from its shipping carton.
Position the DISPLAYCONSOLE above the ACCESSORY
TRAY(W). Connect the WIRE(s) (Z) leading from the DISPLAY
CONSOLE BRACKET (X) to the corresponding JACK(s) located
on the back of the DISPLAY CONSOLE. Secure the DISPLAY
CONSOLE to the DISPLAY CONSOLE BRACKET using four
1/2" PHILLIPS SCREWS (6). Tighten the SCREWS securely. Do
not overtighten the SCREWS.
16. Locate the HANDLEBAR ASSEMBLY(DD). With the handlebars
facing forward, position the HANDLEBAR ASSEMBLYnear the
top of the HANDLEBAR TUBE (L). Connect the WIRES (EE)
leading from the HANDLEBAR ASSEMBLYand the HANDLE-
BAR TUBE. Slide the HANDLEBAR ASSEMBLYfully into the
HANDLEBAR TUBE. Secure the HANDLEBAR ASSEMBLYto
the HANDLEBAR TUBE using four 5/8" BUTTON HEAD
SCREWS (15) and matching FLAT WASHERS (16). Tighten the
SCREWS securely.
CAUTION: Be careful not the pinch the WIRES (EE) when
sliding the HANDLEBAR ASSEMBLY(DD) into the HAN-
DLEBAR TUBE (L).
17. Locate the RIGHT PEDAL (FF) (marked with an "R") and
PEDALSTRAP (GG) (marked with an "R"). With the side of the
PEDALSTRAP marked with an īRī facing upward, slide the slot-
ted end of the PEDAL STRAP through the left slot in the
PEDAL. Fasten one of the slots onto the TAB located under the
left slot of the PEDAL. Bend the PEDAL STRAP upward and
slide the remaining end of the PEDAL STRAP through the right
slot in the PEDAL and into the STRAP ADJUSTMENT CLIP. The
PEDALSTRAP should securely engage the STRAP ADJUST-
MENTCLIP.
18.Install the RIGHT PEDAL (FF) to the USER RIGHT CRANK
ARM (HH). Repeat for the LEFT PEDAL (JJ) (marked with an
"L") and PEDAL STRAP (KK) (marked with an "L").
NOTE: The LEFT PEDAL (JJ) has reverse threads.
19. Position the unit in the desired location for use. The unit can be
easily moved into place by lifting the rear of the unit and rolling it
on the front rollers. Level the unit before use. Refer to the level-
ing instructions stated in the operations portion of this manual.
5