5. Connect the CONNECTOR (J) leading from the HANDLE-
BAR ASSEMBLY(E) with the CONNECTOR (J) leading from
the SEATASSEMBLY (F). Be sure the connectors fully lock.
CAUTION: To ensure that your handsensor heart rate
works properly, secure the HEART RATE CABLE (K) into
the CABLE TIE CLIPS (G). Note the routing of the
HEART RATE CABLE so as to not pinch the HEART
RATE CABLE between the SEATand the SEAT ASSEM-
BLYduring assembly.
6. Locate the SEATBOTTOM (L). Align the SEATBOTTOM
mounting holes with those in the LOWER SEAT SUPPORT
TUBES (M). Secure the SEAT BOTTOM using four 2"
PHILLIPS SCREWS (6) and LOCK WASHERS (7). Tighten
the SCREWS securely.
7. Align the guide rollers located on the underside of the SEAT
ASSEMBLY(F) with the SEATEXTRUSION (N). Carefully
guide the SEATASSEMBLY onto the SEAT EXTRUSION.
Slide the SEATASSEMBLY fully forward. Connect the WIRE
(O) leading from the user left side of the SEAT ASSEMBLY
to the jack located at the left front of the SEAT EXTRUSION.
8. In the hole located in the user right side of the SEATEXTRU-
SION (J), behind SEATASSEMBLY (F), install one 1-3/8"
BUTTON HEAD SCREW with locktite (7), two 15/16" FLAT
WASHERS(8), one RUBBER BUMPER SLEEVE (9) and one
1" RUBBER BUMPER (10) as shown.
9. Mount the SEATADJUSTMENT LEVER (P) to the user right
side of the SEATASSEMBLY (F) using two 3/4" PHILLIPS
SCREWS (11). Tighten the SCREWS securely.
10. Secure the SEATBACK (Q) to the UPPER SEAT SUPPORT
TUBES (R) using four 2" PHILLIPS SCREWS (6) and LOCK
WASHERS (7). Tighten the SCREWS securely.
11. Locate the SEAT EXTRUSION ENDCAP (S). Secure the
SEATEXTRUSION ENDCAP to the SEATEXTRUSION (N)
using two 1/2" PHILLIPS SCREWS (12).
12. Locate the MONOCOLUMN (T). Cut the WIRE TIE securing
the WIRE (U) to the bottom of the MONOCOLUMN. Slide
the MONOCOLUMN COVER (V) onto the MONOCOLUMN
as shown. Slide the MONOCOLUMN COVER up to the
HANDLEBAR TUBE (W).
13. Locate and insert the GROMMET (X) into the SIDE ACCESS
HOLE (Y) of the MONOCOLUMN (T). Pull the WIRE (U) out
through the SIDE ACCESS HOLE.
14. With the HANDLEBAR TUBE (W) facing the rear of the unit
as shown, slide the MONOCOLUMN (T) into the MONO-
COLUMN BRACKET (Z) of the BASE UNIT (C). Slide the
MONOCOLUMN down until it is fully seated. Secure the
MONOCOLUMN to the MONOCOLUMN BRACKET using
two 3-15/16" HEX HEAD BOLTS (13) and three THICK FLAT
WASHERS (14) (as shown) from the front side of the
MONOCOLUMN and two 2-3/8" HEX HEAD BOLTS (15)
and THICK FLATWASHERS (14) from the user left side of
the MONOCOLUMN BRACKET. Tighten the BOLTS secure-
ly.
CAUTION: Be careful not to pinch the WIRE(s) (AA)
leading from the MONOCOLUMN BRACKET (Z) when
inserting the MONOCOLUMN (T) into the MONOCOL-
UMN BRACKET.
15. Connect the WIRE(s) (AA) leading from the MONOCOLUMN
BRACKET (Z) to the corresponding WIRE (U) from the SIDE
ACCESS HOLE (Y) of the MONOCOLUMN. Slide the
MONOCOLUMN COVER (V) downward to the meet the
MAIN SHROUDS (BB). Secure the MONOCOLUMN COVER
to the MAIN SHROUDS using four 1/2" PHILLIPS SCREWS
(12) and matching FLAT WASHERS (16). Tighten the
SCREWS securely. Do not overtighten the SCREWS.
16. Locate the DISPLAYCONSOLE BRACKET (CC) and
ACCESSORYTRAY (DD). While holding the WIRE(s)/CON-
NECTOR (EE), cut the wire tie securing the CONNECTOR
to the MONOCOLUMN (T). Position the DISPLAY CON-
SOLE BRACKET and ACCESSORYTRAY near the top of
the MONOCOLUMN. Feed the WIRE(s)/CONNECTOR lead-
ing from the TOPACCESS HOLE (FF) of the MONOCOL-
UMN through the center hole of the DISPLAY CONSOLE
BRACKET and the ACCESSORYTRAY. Secure the DIS-
PLAYCONSOLE BRACKET and the ACCESSORY TRAY to
the MONOCOLUMN using two 1" PHILLIPS SCREWS (17)
and matching FLATWASHERS (18). Tighten the SCREWS
securely.
CAUTION: Be careful not the pinch the WIRE(s)/CON-
NECTOR (EE) leading from the MONOCOLUMN (T)
when securing the DISPLAY CONSOLE BRACKET (Z)
and ACCESSORYTRAY (DD) to the MONOCOLUMN.
NOTE: Be careful not to let the WIRE(s)/CONNECTOR (EE)
fall into the MONOCOLUMN (T).
17. Remove the DISPLAYCONSOLE (GG) from its shipping
carton. Position the above the ACCESSORY TRAY(DD).
Connect the WIRE(s)/CONNECTOR (EE) leading from the
DISPLAYCONSOLE BRACKET (Z) to the corresponding
JACK(s) located on the back of the DISPLAY CONSOLE.
Secure the DISPLAYCONSOLE to the DISPLAY CONSOLE
BRACKET using four 1/2" PHILLIPS SCREWS (12). Tighten
the SCREWS securely. Do not overtighten the SCREWS.
18. Locate the HANDLEBAR ASSEMBLY(HH). Position the
HANDLEBAR ASSEMBLYnear the top of the HANDLEBAR
TUBE (W). Slide the HANDLEBAR ASSEMBLY fully into the
HANDLEBAR TUBE. Secure the HANDLEBAR ASSEMBLY
to the HANDLEBAR TUBE using four 5/8" BUTTON HEAD
SCREWS (3) and matching FLAT WASHERS (4). Tighten
the SCREWS securely.
19. Locate the RIGHT PEDAL (JJ) (marked with an "R") and
PEDALSTRAP (KK) (marked with an "R"). With the side of
the PEDAL STRAP marked with an īRī facing upward, slide
the slotted end of the PEDAL STRAP through the left slot in
the PEDAL. Fasten one of the slots onto the TAB located
under the left slot of the PEDAL. Bend the PEDAL STRAP
upward and slide the remaining end of the PEDAL STRAP
through the right slot in the PEDAL and into the STRAP
ADJUSTMENT CLIP. The PEDALSTRAP should securely
engage the STRAP ADJUSTMENT CLIP.
20. Install the RIGHT PEDAL (JJ) to the USER RIGHT CRANK
ARM (LL). Repeat for the LEFT PEDAL (MM) (marked with
an "L") and PEDAL STRAP (NN) (marked with an "L").
NOTE: The LEFT PEDAL (MM) has reverse threads.
21. Position the unit in the desired location for use. The unit can
be easily moved into place by lifting the rear of the unit and
rolling it on the front rollers. Level the unit before use. Refer
to the leveling instructions stated in the operations portion of
this manual.
7