READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE

This fixture is intended for installation in accordance with the National Electrical Code and local regulations. To assure full compliance with local codes and regulations, check with your local electrical inspector before installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.

Retain these instructions for maintenance reference.

4.Using the wire provided in parts bag; pass approximately half the length of each black, white and green wire through opening in back of FIXTURE HOUSING. (Fig. 2)

INSTRUCTION SHEET NO.

IS:46531

0198

Page 2 of 3

5. Position LINEAR ADAPTER COVER over back of FIXTURE HOUSING

allowing two THREADED STUDS to pass through mounting holes

surrounding KNOCK-OUT OPENING.

Caution: Make certain not to pinch wires between FIXTURE

HOUSING and LINEAR ADAPTER. Secure LINEAR ADAPTER in

place by placing LOCK WASHERS and HEX NUTS (from front of

fixture housing) over threaded STUDS and fully tighten.

6. Carefully pull supply wires from outlet box through center

KNOCK-OUT HOLE and mount FIXTURE HOUSING to outlet box

using outlet box screws (provided with outlet box).

Note: In addition to outlet box mounting, it is also recommended

to use AUXILIARY MOUNTING HOLES at each end of

FIXTURE HOUSING. (Fig. 1) Use appropriate mounting

hardware for the wall surface (i.e.: wood screws, toggle

bolts, molly screws, etc.).

7. In second adjoining FIXTURE HOUSING, remove SMALL

DIAMETER KNOCK-OUT in the end closest to first FIXTURE and

snap PLASTIC BUSHING into opening.

8. Pass the other half of black, white and green wires through

opening.

9. Position second FIXTURE HOUSING over end of LINEAR ADAPTER

allowing MOUNTING STUDS on ADAPTER to pass through

MOUNTING HOLES in back of FIXTURE HOUSING. Secure FIXTURE

HOUSING to wall surface using appropriate mounting hardware

for the wall surface (i.e.: wood screws, toggle bolts, molly

screws, etc.).

Note: If additional FIXTURES are to be installed; follow steps 3

through 5 prior to mounting second FIXTURE HOUSING.

Secure LINEAR ADAPTER in place by placing LOCK WASHER

and HEX NUT (from front of fixture housing) over threaded

SMALL DIAMETER

KNOCK-OUTS

AUXILIARY

MOUNTING

HOLES

SMALL DIAMETER

KNOCK-OUTS WITH

PLASTIC BUSHING

LOCK

WASHER

HEX

 

 

 

CENTER

 

 

KNOCK-OUT

NUT

 

 

 

 

 

KNOCK-OUT

SLOTS

FIXTURE

HOUSING

LINEAR ADAPTER COVER

THREADED

STUD

WIRE:

BLACK, WHITE, & GREEN (provided with fixture)

Fig. 2

BACK-VIEW OF FIXTURE HOUSING

STUDS and fully tighten.

10. Make electrical connections: FIXTURE HOUSING containing

supply wires (in coming power); connect black fixture lead and

black wire from LINEAR ADAPTER to black (hot) supply lead;

white fixture lead and white wire from LINEAR ADAPTER to

white (neutral) supply lead. Green fixture wire and green LINEAR

ADAPTER wire are ground wires and must be connected to a

ground screw or ground lead within outlet box. Use wire nuts

(local hardware item) to make connections. Carefully push all

wire connections through center opening making certain all

connections are inside of outlet box.

11. Using WIRE NUTS (provided with fixture) connect second fixtures

black lead to black LINEAR ADAPTER lead; white fixture lead to

white LINEAR ADAPTER lead; green fixture lead (ground) to

green LINEAR ADAPTER lead. Repeat procedure if other fixtures

are installed in continuous run.

12. Re-install REFLECTOR by placing two TABS on REFLECTOR into

SLOTS in FIXTURE HOUSING and pivot REFLECTOR back until

HOLES in REFLECTOR aligns with HOLES in FIXTURE HOUSING.

Secure REFLECTOR in position by re-installing two REFLECTOR

SLOT

SLOT

FINGER

NOTCH

SPRING CLIP

DIFFUSER DOOR

 

 

ALLEN

ALLEN

 

SCREW

 

 

 

 

 

 

 

DRAW

 

 

 

 

 

BOLT

WRENCH

 

 

 

 

 

 

 

 

 

 

 

NOTCH

SPRING

CLIPMOUNTING BOSS

MOUNTING SCREWS. Repeat procedure for remaining FIXTURES

in run.

Fig. 3

LIGHTOLIER a GENLYTE company.

631 Airport Road, Fall River, MA 02720

Page 2
Image 2
Lightolier IS:46531 Surrounding KNOCK-OUT Opening, Using outlet box screws provided with outlet box, Screws, etc, Run