Lighting Systems PTS7-1, Features, Electrical, Finish

Lighting Systems PTS7-1

1BHFPG1FSJNFUFS5SPVHI3FDFTTFE%JSFDU-PVWFS-JHIU51FS'PPU4FDUJPO

	11-1/4” (28.58cm)
	5
7 -1/16”	2	3
(19.94cm)	2	3
1
1-5/16” (3.33cm)	6	4
	8-1/4” (20.96cm)

Complete ordering instructions on back.

Quarter Scale

Sample Run, End Plate and Corner Block Accessories

Example of Straight Run

Example of Pattern Run

End Cap Set

PTS7EP Standard

PTS7EPA Air

21' 10-3/4” (677.39cm)

	60"			84"			84"

Lighted

Telescoping

Unit

	10' 2-1/4” (310.52cm)	14" (35.56cm)
	9' 0” (274.32cm)	14" (35.56cm)
	9' 0” (274.32cm)	14" (35.56cm)
		14" (35.56cm)
	60"

90° Inside Corner	48"	8' 1/2”

1-1/2”

(3.81cm)

(245.11cm)

Telescoping

Unit (3 places)

1-1/2” (3.81cm)

8' 1/2”

245.11cm

90° Inside

PTS7C901 Standard PTS7C901A Air

90° Outside

PTS7C900 Standard PTS7C900A Air

135° Inside

PTS7C1351 Standard PTS7C1351A Air

135° Outside

PTS7C1350 Standard PTS7C1350A Air

48"

90° Outside Corner

1-1/2” (3.81cm)

Features

1.Housing: Die-formed steel, slotted for air return. Integral flanges at each end strengthen the housing and permit housings to be bolted together in continuous runs and facilitate suspension of fixture. Concealed openings for heat extraction and air return.

2.Lamping: One T8 or T12 fluorescent lamp, as specified. Provided by others.

3.Reflector: Die-formed semi-specular aluminum.

4.Louver: Semi-specular anodized aluminum, 40° lengthwise by 30° minimum crosswise shielding. Supported along both edges by concealed frame of extruded aluminum. Bold baffle, prismatic lens, gold anodized louver, open or egg crate louver available, consult factory.

5.Socket Channels: Die-formed, pre-painted steel held by support brackets and allows for up to 6” (15.24cm) lamp overlap.

6.Ceiling Trim: Extruded aluminum with integral aligner splines.

Electrical

Specify 120 volt or 277 volt. 3 conductor, 18 gauge wire. Color-coded quick connectors allow ease of connection for joiner modules. For special circuiting, consult factory. Factory installed ballast disconnect allows the ballast to be disconnected from and reconnected to incoming power under load without turning the entire circuit off.

Dimming: Advance Mark X, use Advance compatible two-wire control (no extra control lead required).

Mountings

Wall Adjustment Bracket - Allows for inconsistencies in wall straightness. Die-formed steel used to mount system to the wall.

Finish

Ceiling trim painted baked enamel semi-gloss white.

Options and Accessories

90° inside, 90° outside, 135° inside, and 135° outside corerns available.

Labels

UL, cUL and I.B.E.W.

Job Information

Type:

Job Name:

Cat. No.:

Lamp(s):

Notes:

"JSQPSU3PBE'BMM3JWFS."t t'BY

We reserve the right to change details of design, materials and finish.

XXXMJHIUPMJFSDPN½1IJMJQT(SPVQt #

Lightolier manual Lighting Systems PTS7-1, Features, Electrical, Mountings, Finish, Labels

Models: PTS7-1