|
|
| blockage or damage. If above checks are okay, but |
|
|
|
| pressure switch is still not closed, replace gas valve. |
|
|
| Air pressure switch | Check air switch terminals for supply voltage to |
|
|
|
| terminals NO2 and COM. If voltage is present on one |
|
|
|
| side only, check for air tube blockage or misalignment. |
|
|
|
| If these are okay, adjust air pressure switch or replace |
|
|
|
| if necessary. |
|
|
| Oven cavity | Terminals are normally closed, opens at 660°F (350°C). |
|
|
|
| If open, reset and test oven for proper operation. If |
|
|
|
| thermostat will not hold for maximum oven temperature, |
|
|
|
| and oven is not exceeding control setting, check for |
|
|
|
| proper location of capillary bulb in its spring holder. If |
|
|
|
| above checks are okay, replace |
|
|
| Ignition control | Check for proper supply voltage to ignition control. |
|
|
|
| Check for proper voltage to the burner blower motor. |
|
|
|
| This can be checked at motor connecting plug |
|
|
|
| terminals 2 and 5. If voltage is present, proceed with |
|
|
|
| next step, if not, wait 30 seconds, push reset button |
|
|
|
| and try to restart. If this fails, check wires from |
|
|
|
| thermostat and burner blower motor to the ignition |
|
|
|
| control. If the above checks okay, replace ignition |
|
|
|
| control. |
|
|
| Burner blower motor | Check for supply voltage to motor. WITH POWER OFF: |
|
|
|
| Turn blower wheel to check for locked rotor. If supply |
|
|
|
| voltage is present at motor connecting plug terminals 2 |
|
|
|
| and 5, and motor does not run, replace burner blower |
|
|
|
| motor. |
|
|
| Air pressure switch | Check for proper supply voltage switching from “NC” to |
|
|
| (burner blower) | “NO” on ignition control. Check for air pressure switch |
|
|
|
| adjustment, air tube blockage or misalignment. If these |
|
|
|
| adjustments fail, replace air pressure switch. |
|
|
| Spark generator | A |
|
|
|
| burner blower motor starts. Check for supply voltage at |
|
|
|
| spark generator. If voltage is not present, check reset |
|
|
|
| button for ignition control. If voltage is still not present, |
|
|
|
| replace ignition control. If there is input voltage to the |
|
|
|
| spark generator, but there is no high voltage output, |
|
|
|
| replace the spark generator. |
|
|
| Igniter/sensor assembly | Check this assembly for visible damage. Replace as |
|
|
|
| needed. If there is no visible damage, check for voltage |
|
|
|
| supply to igniter/sensor assembly. If there is voltage |
|
|
|
| supplied to the igniter/sensor, but there is no spark, |
|
|
|
| replace igniter/sensor assembly. |
|
|
| Gas valve | Gas valve should open when proper supply voltage is |
|
|
|
| present. If there is no voltage present, check reset |
|
|
|
| button on ignition control, and all connections for |
|
|
|
| tightness. If there is still no voltage to gas valve, |
|
|
|
| replace the ignition control. If there is voltage to the gas |
|
|
|
| valve, check for gas pressure at the gas pressure tap |
|
|
|
| (located in the gas piping just prior to the burner). If |
|
|
|
| there is no gas pressure, replace the gas valve. |
|
| Flame will not stay on | Flame sensor | To check for flame sensor operation, connect a digital |
|
|
|
| multimeter (capable of measuring DC microamps) |
|
|
|
| between the flame sensor wire and terminal #1 on the |
|
|
|
| ignition control. Sensor current is to be 3 microamps, |
|
|
|
| minimum. If these readings are not achieved, replace |
|
|
|
| igniter/sensor assembly. Also check for any type of |
|
|
|
| damage to flame sensor wire and connections. |
|
|
|
| NOTE: The DC microamp test must be conducted with |
|
|
|
| the oven in low flame (bypass) operation. |
|
Impinger II – Advantage Digital Service Manual - International | 9 |