SPACING

The oven must have 5 inches (127 mm) of clearance from combustible surfaces. In case other equipment is located on the right side of oven, a minimum clearance of 24 inches (609 mm) is required from that equipment.

FOR ALL OVENS: A 24-inch (609 mm) clearance at the rear of the oven must be obtainable for service access.

FOR 1000 and 1400 OVENS: A permanently installed (unmovable) oven requires a minimum of 11 feet clearance

on the right hand side to allow for conveyor removal, cleaning, and servicing. NOTE: On 1200 Series, 11 feet on left.

NOTE: Do not install this (these) oven(s) in any area with an ambient temperature in excess of 95°F / 35°C. Doing so will cause damage to the unit.

!CAUTION: Oven must be operated on approved basis only.

VENTILATION

A VENT IS REQUIRED: Local codes prevail. These are the “authority having jurisdiction” as stated by the NATIONAL FIRE PROTECTION ASSOCIATION, INC. in NFPA 96 latest edition. In addition, to be in compliance with the NFPA 54 Section 10.3.5.2, this unit must be installed with a ventilation hood interlock that prevents the unit from operating when the ventilation hood is off. For further ventilation information, see below.

VENTILATION GUIDELINES

A ventilation hood is required to remove heat and cooking odors. For gas ovens, a ventilation hood is also required to remove the products of combustion. The hood and HVAC installation must meet local codes to gain approval by the authority having jurisdiction. Requirements may vary throughout the country depending on the location by city, county, and state. Obtain information from the authority having jurisdiction to determine the requirements for your installation. Obtain information and review copies of codes or documents that will be used to inspect and approve your installation. Your ventilation hood supplier and HVAC contractor should be contacted to provide guidance. A properly engineered and installed ventilation hood and HVAC system will expedite approval and reduce oven maintenance costs. Proper ventilation is the oven owner’s responsibility.

The ventilation hood must operate in harmony with the building HVAC system. It typically requires between 1200 and 3500 CFM exhaust. (The “Efficiency” of various hood designs makes it necessary to specify such a wide range of ventilator CFM.) Make up air must be supplied by either a hood design or the HVAC system. This will vary with hoods from various manufacturers.

CAUTION: Prevent airflow through the cooking tunnel. Air must NOT be directed onto the oven front or at side of cooking area or rear of oven.

Performance will be evaluated during Start-up Checkout by conducting a smoke candle test. The hood must capture all smoke from the oven. This is required to assure proper performance of the oven and to eliminate additional service calls that occur when ambient temperatures are too high. In all cases, the ambient temperature around the oven must be less than 95°F / 35°C when the oven is operating. In certain localities, other chemical or gaseous methods of detecting adequate capture will be the requirement to meet the local code authority.

The drawing shown on page 8 is a typical installation and is intended to be a guideline. It is not a rigid specification. Hood dimensions and the positioning of the hood over the oven will vary with hood manufacturers.

NOTE: Lincoln can provide oven spec sheets that show the dimensions of the oven, KW or BTU ratings and other information that will be useful to both the ventilation hood supplier and the HVAC contractor.

IN AUSTRALIA: Refer to Standard AS 5601. This standard specifies the requirements for piping, flueing, ventilation and appliance installation associated with use of or intended use of fuel gases. The requirements of AS 5601 are to be used in conjunction with, but do not take precedence over, any statutory regulations that may apply in any area.

Impinger I – 1000 Series Ops Manual

7

Page 6 Page 8
Page 7
Image 7
Lincoln 1200, 1400, 1000 operating instructions Spacing, Ventilation Guidelines
Page 6 Page 8

1000, 1200, 1400 specifications

The Lincoln series, particularly the models Lincoln 1000, 1200, and 1400, represents an evolution in luxury vehicles, combining elegance with cutting-edge technology. Each model builds upon its predecessor while introducing features that enhance performance, comfort, and safety.

Starting with the Lincoln 1000, this model set the foundation for the series. It showcased a refined design characterized by sleek lines and an impressive presence on the road. The Lincoln 1000 was equipped with a powerful engine, delivering smooth acceleration and a quiet ride. Interior features included premium materials such as leather upholstery, real wood accents, and a state-of-the-art sound system. Additionally, it offered advanced climate control systems, ensuring passenger comfort. Safety features were also prioritized, with multiple airbags and stability control systems included to enhance driver confidence.

Moving on to the Lincoln 1200, this model took luxury to the next level. The exterior design was more aggressive, with a revised grille and enhanced aerodynamics for better fuel efficiency. The engine options expanded, offering hybrid technology for environmentally conscious consumers without sacrificing power. Inside, the Lincoln 1200 featured an upgraded infotainment system, incorporating a larger touchscreen display along with smartphone integration for connectivity on the go. This model also introduced adaptive cruise control and lane-keeping assist, showcasing Lincoln’s commitment to safety and innovation.

The Lincoln 1400 represents the pinnacle of this series. This model incorporates all the advancements of the previous iterations while introducing next-generation technologies. A hybrid powertrain with electric capabilities provides a quieter, more efficient drive. The design includes sophisticated lighting technology, such as adaptive LED headlights that adjust to road conditions. Inside, the cabin has been transformed into a haven of luxury, with customizable ambient lighting, heated and ventilated seats, and an advanced noise cancellation system for a serene driving experience. Furthermore, the Lincoln 1400 emphasizes driver assistance technology, featuring an array of sensors and cameras to support features like automatic parking and enhanced collision prevention systems.

In conclusion, the Lincoln 1000, 1200, and 1400 models showcase a remarkable journey of luxury and technology, with each iteration bringing forth innovative features and design enhancements that elevate the driving experience. As Lincoln continues to evolve, the commitment to craftsmanship, comfort, and cutting-edge technology remains central to its identity.
Top Page Image Contents