Summary of Welding Processes, Stick Auto | Lincoln Electric 8

	B-5			OPERATION		B-5

			Summary of Welding Processes

			CONTROL		ELECTRODE
			CABLE	IDLE	WHEN NOT	TO START
		PROCESS	USED	MODE	WELDING	WELDING
	STICK		No	AUTO	Hot	Touch electrode to work.
						Welding starts immediately
						and engine goes to high
						idle.

	TIG/K7930-1/K938-1,		Yes	HIGH	Cold	Press Amptrol, contactor
	K936-( ) /K892-1					closes, welding
	(WITH AMPTROL)					starts immediately.

	WIRE FEED, LN-25 WITH		No	AUTO	Cold	Press gun trigger, LN-25
	INTERNAL CONTACTOR					contactor closes. Welding
						starts immediately and
						engine goes to high idle.
						NOTE: Output Control
						must be set above “3”.
	WIRE FEED, LN-7 WITH		Yes	HIGH	Cold	Press gun trigger,
	K240 CONTACTOR KIT					contactor closes. Welding
						starts immediately.

RANGER 8

Image 22

Lincoln Electric 8 manual Summary of Welding Processes, Stick Auto

Contents

Safety Depends on You Ranger Safety California Proposition 65 Warnings Electric Shock can kill Welding Sparks can cause fire or explosion Iii Précautions DE Sûreté Sûreté Pour Soudage a L’Arc Thank You Please Examine Carton and Equipment For Damage Immediately Table of Contents K2160-1 CSA Meets Canadian STD InstallationHeight Width Depth Weight Ranger 20 B 100 150 200 250 SpecificationsDC Wire Feed CV Output CV Output Range Output Amps DC Stick / TIG CC Output Output Range Spark Arrester Installation InstructionsSafety Precautions Machine Grounding Welding Output Cables Pre-Operation ServiceAWG High Altitude Operation Connection of Lincoln Electric Wire FeedersAngle of Operation Location / Ventilation Instructions Additional Safety PrecautionsAuxiliary Power Connection of K930- TIG Module to the Ranger Duplex Receptacles Motor Starting These Devices Without Additional Resistive Type Loads Electrical Device USE with the RangerType Common Electrical Devices Possible Concerns Not USE These Devices With a Ranger Simultaneous Welding and Power Auxilliary Power While WeldingStandby Power Connections Connection of Ranger 8 to Premises Wiring Operation Design FeaturesOther Features General Description Onan P216 Kohler Honda 16 H.P. Performer 20 H.P. Command Engine ON-OFF SwitchEngine Start Push-Button Switch Ranger 8 Approximate Fuel Consumption Break-in Period Starting/Shutdown InstructionsStopping the Engine Stick Constant Current Welding Wire Feed Welding Processes Constant VoltageWelding Process TIG Constant Current Welding Summary of Welding Processes Stick Auto Accessories K1745-1 Single GAS Cylinder Holder Stick Wire FeedRecommended Equipment TIG Safety Precautions MaintenanceCH20S Overspeed is Hazardous Onan P216 Kohler CH20S Honda GX620 Troubleshooting HOW to USE Troubleshooting Guide Troubleshooting Troubleshooting Diagrams K1418-1 Code 10373 & 10535 Ranger 8 Onan Wiring Diagram ALL Case Front Components Shown Viewed from Rear K1419-1 Code 10375 & 10537 Ranger 8 Kohler Wiring Diagram ALL Case Front Components Shown Viewed from Rear K2160-1 Code 10886 Ranger 8 Honda CSA Wiring Diagram Connection of Ranger 8 to LN-7 & K240 Contactor KIT M17215-2 30-98E M17215-3 30-98E Ranger Need Welding Training? How To Read Shop DrawingsNew Lessons in Arc Welding Basic Course Precaucion Warnung