
TROUBLESHOOTING |
| ||||
|
|
|
|
| |
| TROUBLESHOOTING GUIDE |
|
| Observe Safety Guidelines | |
|
| detailed in the beginning of this manual. | |||
|
|
|
|
| |
| PROBLEMS | POSSIBLE AREAS OF |
| RECOMMENDED | |
| (SYMPTOMS) | MISADJUSTMENT(S) |
| COURSE OF ACTION | |
|
|
|
|
|
|
|
| OUTPUT PROBLEMS |
|
|
|
| The Beeper (Piezoelectric Buzzer) cannot be | 1. Background noise may be too loud for user |
|
|
|
| heard – machine operating normally. | to hear beeper. |
|
|
|
|
|
|
|
|
|
| The welding parameters that were | 1. Make certain that a remote control unit is |
|
|
|
| saved in memory are different | not connected. When a remote control unit is |
|
|
|
| when recalled. | used, the weld parameters are set by the |
|
|
|
|
| remote control potentiometers. |
|
|
|
|
|
|
|
|
|
| The water cooler does not turn on. | 1. Make sure that the water cooler has been |
|
|
|
| enabled. Refer to the Setup Overlay descrip- |
|
|
| |
|
|
|
|
| |
|
| tion in the Operation Section of this manual. |
|
|
|
|
| 2. If the water cooler is enabled but there is |
|
|
|
|
| insufficient pressure in the water cooler hose, |
|
|
|
|
| the machine will beep loudly and the water |
|
|
|
|
| cooler will shut down. In this case, prime the |
|
|
|
|
| water cooler. Refer to the Setup Overlay |
|
|
|
|
| description in the Operation Section of this |
|
|
|
|
| manual. |
|
|
|
|
|
|
| If all recommended possible areas | |
| The machine beeps without the | If the water cooler is enabled and the pres- |
| ||
| keys being pressed. | sure switch inside the water cooler opens (due |
| of misadjustments have been | |
|
| to inadequate pressure in the water cooler |
| checked and the problem per- | |
|
| hose), the machine indicates this by beeping. |
| sists, contact your local Lincoln | |
|
| This happens regardless of the overlay placed |
| Authorized Field Service Facility. | |
|
| on the machine. In this case do the following: |
|
|
|
|
| 1. Turn the machine off and on a couple of |
|
|
|
|
| times and see if the beeping continues. If the |
|
|
|
|
| pressure dropped momentarily then turning |
|
|
|
|
| the machine off and on eliminates the beep- |
|
|
|
|
| ing. A momentary pressure drop could be due |
|
|
|
|
| to someone stepping on the water cooler |
|
|
|
|
| hose, for example. |
|
|
|
|
| 2 Check the water cooler hose for kinks and |
|
|
|
|
| other places of reduced water flow. If such |
|
|
|
|
| problems were found then correct them and |
|
|
|
|
| turn the machine off and on to check if the |
|
|
|
|
| beeping has been eliminated. |
|
|
|
|
| 3. Check the water cooler fluid level. Low fluid |
|
|
|
|
| level could cause the pressure to drop. |
|
|
|
|
| 4. Prime the water cooler. Refer to the Setup |
|
|
|
|
| Overlay section of this manual for instructions. |
|
|
|
|
|
|
|
|
|
CAUTION
If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, con- tact your local authorized Lincoln Electric Field Service Facility for technical assistance.
POWER WAVE 450