Lincoln Electric IM610-A manual Wiring Diagrams, SP-175 Plus Wiring Diagram Code

SP-175 Plus WIRING DIAGRAM CODE 10542

CUSTOMER VOLTAGE RECONNECTION FOR DUAL VOLTAGE MACHINE								Do not operate with covers removed.
MACHINES ARE SHIPPED FROM FACTORY CONNECTED FOR 230V AS SHOWN. TO CONNECT WELDER FOR								Disconnect input power by unplugging
208V INPUT. DISCONNECT WELDER FROM INPUT POWER, REMOVE CASE SIDE, REMOVE LEAD MARKED H1
FROM TAB TERMINAL H1. REMOVE TAPE SECURING H3 TO LEAD SLEEVING AND CONNECT H3 TO TAB					ARC VOLTAGE			power cord before servicing
TERMINAL H1. INSULATE UNUSED H1 LEAD FOR 300V WITH ELECTRICAL TAPE AND SECURE TO LEAD								Do not touch electrically live parts
SLEEVING, REINSTALL CASE SIDE BEFORE CONNECTING INPUT POWER. RECONNECTION TO 230V IS					5K
REVERSE OF ABOVE PROCEDURE. SEE INSTRUCTION MANUAL FOR DETAILS.								Only qualified persons should install, use or
					R1		HIGH VOLTAGE
								service this machine.
7		7	CONTROL P.C. BOARD		205	207	can kill
	208/230 60Hz
					206
	GAS		( J2 )	*
32A	SOLENOID	32A					JUMPERED PLUG STANDARD
		( J1 )*					SPOT/STITCH TIMER OPTIONAL

																						WIRE SPEED			N.C.												THERMOSTAT
																								5K
																									*										RF CHOKE		(MOUNTED TO
																								R2													SEC. COIL)
																									( J3 )										AS'BLY
				H1	31A	32	1	2	3	4	5	6	1	2	3	4	5	6	7	8	9	10
																										5		4	3	2		1
																																			GUN TRIGGER
	TO EARTH																					208			210
																								209
	GROUND PER									205 206			541 539			204	210 209			213	211 208
		H3		H1			207								203																				THERMOSTAT
	NATIONAL,																									215						213
		(208V)	(230V)														215																		(MOUNTED TO
	LOCAL OR
																																			DIODE HEATSINK)
	OTHER
SP-175	APPLICABLE																															213A				541	+
	ELECTRICAL				FAN
																																				539
	CODES.
					MOTOR
																						204
PLUS		S1		L1														204		203				OUTPUT CHOKE			+			GUN CABLE						WIRE FEED MOTOR
																													CONDUCTOR BLOCK
	G						24 VAC
																						204
			L2				AUX WDG.
	ON-OFF						CIRCUIT															204
	SWITCH						BREAKER				31A	H1			D1		D5					204
											H3
																	D2		D6											.0047		f
						31								202										+
		N.C.																				120,000	f								3KV
														N.A.											N.D.
																						50V
														N.D.										C1
	CASE													201																.0047		f
	GROUNDING				H2
													T1								N.B., N.D.										3KV					CASE
	STUD																D4
																			D8						-
																																				GROUNDING
	ELECTRICAL SYMBOLS PER E1537														D3		D7			203		203												TO		STUD
																			203															WORK
																						203				J1						J2			J3	LATCH
	NOTES:																								1	2	3			1	2	3	4	5
	N.A. DIODES D1, D3, D5 & D7 ARE MOUNTED ON THE OUTSIDE HEATSINK.																		*CONNECTOR CAVITY NUMBER
	N.B. DIODES D2, D4, D6 & D8 ARE MOUNTED ON THE INSIDE HEATSINK,																								4	5	6			6	7	8	9	10	5 4 3 2 1
	WHICH IS CLOSEST TO THE CENTER PANEL.
	N.C. COMPONENT VIEWED FROM REAR.																												LATCH					LATCH
	N.D. BOLTED ALUMINUM CONNECTIONS REQUIRE T12837 JOINT																											CAVITY NUMBERING SEQUENCE
	COMPOUND (DOW CORNING 340) WHEN REATTACHING.																											(COMPONENT SIDE OF BOARD)									4-16-99G
																																					M19060

NOTE: This diagram is for reference only. It may not be accurate for all machines covered by this manual. The specific diagram for a particular code is pasted inside the machine on one of the enclosure panels.

F-1

WIRING DIAGRAMS

F-1