Lincoln Electric IM911 Accessories, K559-2 Cooler Horizontal Mounting Bracket, Coolant Hoses

C-1 ACCESSORIES C-1

OPTIONAL EQUIPMENT (Field Installed)

K559-2 Cooler Horizontal Mounting Bracket:

Mounts the COOL ARC® 40 horizontally to the top of a power source, securing the cooler to the lift bale. The kit includes all necessary mounting hardware.

K559-3 Cooler Vertical Mounting Bracket:

Mounts the COOL ARC® 40 vertically to a power source that has a dual cylinder undercarriage already installed. The bracket securely mounts the cooler to the dual cylinder support bracket. The kit includes all necessary mounting hardware.

K1536-1 Magnum Flow Sensor:

Protects valuable torches, guns and robotic welding systems from damage when loss of coolant flow has occurred for any reason such as a blocked or kinked water line or a ruptured hose.

KP1529-1 Quick Connect Water Adapter:

Converts a male 5/8"-18 left hand hose fitting (CGA Style) to a female quick connect fitting. The female quick connect mates with the male quick connects on water cooled MIG guns or hoses.

K1859-1 Water Cooler Hoses (5/8" LH CGA to QD):

This kit includes two 25ʼ – 3/16 I.D. water hoses with a 5/8" LH CGA style fitting on one end and a male quick disconnect on the other. Most wire feeders have female quick disconnects and this kit allows direct hook up between the water cooler and the wire feed- er.

K1859-2 Water Cooler Hoses (5/8" LH CGA to 5/8 LH CGA)

“The connector and nipple listed fit tightly onto 5/32" (4.0mm) to 3/16" (4.8mm) inner diameter hose, but if clamped tightly to the hose, can fit up to a .25 (6.4mm) inner diameter hose. These fittings are also readily available from any industrial welding supplier.

K529-10 Power Input Cable with Water and Gas Hoses:

This cable assembly includes the following: (1) power cable, (1) control cable, (1) gas hose and (2) water hoses. The cable assembly connects a power source to a wire feeder for water-cooled MIG applications. The cable length is 10'. The water hoses have 5/8"- 18 left hand male hose fittings and the gas hose has a 5/8"-18 right hand male hose fitting. The cable and hose lengths are designed to connect a wire feeder to a COOL ARC® 40 that is vertically mounted at the rear of a power source on a dual cylinder undercar- riage. Refer to Figure 5 for an illustration of this con- nection.

KP504 TIG Hook Up Kit:

The Hook-Up Kit includes: (2) water hoses, (1) gas hose, (2) water adapter fittings, male to male 5/8" LH thread, (1) water hose coupler, female to female 5/8" LH thread and (1) power cable adapter. Threads on all hoses and fittings are CGA style.

CAUTION

DO NOT USE A WATER SOLENOID VALVE with the COOL ARC® 40. When a solenoid valve clos- es, the pump would dead-head, causing the pump to heat up excessively leading to premature failure of the pump.

------------------------------------------------------------------------

Coolant Hoses:

This kit includes two 7.6 m (25 Ft.)-4.7 mm (3/16”) inside diameter hoses with a 5/8” LH CGA style fitting on both ends. Hoses can be mated with KP1529-1 for a water Cooler to MIG gun application. Ideal for water Cooler to Machines or wire feeders with 5/8” LH CGA style fittings.

Field Installed CGA style hose fittings:

Fittings to convert a standard 4.7 mm (3/16") I.D. hose to a 5/8"-18 left hand male hose fitting. These male fit- tings mate with the fittings on the back of the COOL ARC® 40.

Order the following:

(2) Connector Nuts (T15007-2)

(2)Nipples for 3/16" I.D. Hose (T15008)

(2)Hose Clamps (S10888-35)

Coolant hoses are readily available from an industrial welding supplier or in MIG or TIG hook-up kits provid- ed by Lincoln Electric. Refer to Magnum accessory lit- erature sheets.

For lengths of coolant hoses over 7.6 m (25 Ft.) and up to 15.2 m (50 Ft)., 7.9 mm (5/16”) I.D. hose is rec- ommended. 7.9 mm (5/16”) I.D. hose and accommo- dating fittings are available from an industrial welding supplier.

COOL ARC® 40