Trunking Rules | Lindy 25010 specs

Image 28

Lindy 25010 user manual Trunking Rules

Contents

GIGA Smart Switch 24 + User ManualEnglish LINDY NoPage Start to Manage This Switch Configuration Functions for the SwitchConfigurations Port Configuration System Setup Firmware Update2.11.1.1 Firmware Update Via TFTP 2.11.1.2 Firmware Update Via BOOTP/TFTP 1 Introduction Main Features 1.1 Start to Manage This Switch „ IP address 1.2 Configuration Functions for the Switch 2 Configurations 2.1 Port Status 2.2 Port Configuration 9 Fibre -Enable, Copper -Enable - to enable both mediaz 2 Options for combo ports Port1 and Port2 z 2 Options for ordinary ports Port3 to Port24, copper media only ¾ 100Mbps Full - to set the speed 100Mbps in full duplex mode 2.3 About the Copper/Fibre Media Auto-Detection 2.4 Port Statistics 256-511 BytePkts 512-1023 BytePkts 1024-1522 BytePkts FCSErrors AlignErrors SymbolErrors FragmentPkts OverSizePktsUnicastPkts MulticastPkts BroadcastPkts Single Collision Multi Collisions 64 BytePkts 65-127 BytePkts 128-255 BytePkts 2.5 Port-Based VLAN VLAN and 802.1Q VLAN cannot co-exist at the same time 2.5.1 Add Port-Based VLAN Groups Page Pressing the Remove This VLAN button results in the following 2.5.2 Delete Port-Based VLAN GroupsNow all ports are set to the members in VLAN group No.1 2.5.3 Edit Port-Based VLAN Groups 2.6 802.1Q VLAN 2.6.1 Enable/Disable VLAN 2.6.2 802.1Q VLAN Port Configuration 2.6.3 802.1Q VLAN Config The VID entry VID=200 is successfully deleted Finally, click the Apply button to do the changes ¾ SA Source MAC Address ¾ DA Destination MAC Address 2.7 Trunk¾ SA + DA both SA and DA following section will list the related rules for this function 2.7.1 Trunking Rules Page 2.7.2 Get/Refresh the Latest Trunk Settings 2.7.3 Enable Trunk ¾ Step 3 Click the Apply button to enable trunk settings¾ Step 1 Choose the Distribution Criterion ¾ Step 2 Choose the member ports up to 8 ports for each trunk group 2.7.4 Modify Trunk Settings ¾ Step 3 Click the Apply button to modify trunk settings ¾ Step 2 Click the Apply button to disable trunk 2.7.5 Disable Trunk¾ Step 1 Click the Not Trunking 2.8 Port Mirroring 2.8.1 Get/Refresh the Latest Mirror Settings 2.8.2 Enable Mirror ¾ Step 4 Click the Apply button to enable mirroring settings¾ Step 1 Choose Mirror option to be Mirror All Frames ¾ Step 2 Choose the Monitored Port to be Port16 2.8.3 Modify Mirror Settings ¾ Step 4 Click the Apply button to modify mirroring settings¾ Step 1 Change Mirror option to be Mirror Outgoing Frames ¾ Step 2 Change the Monitored Port to be Port3 ¾ Step 1 Choose Mirror option to be Disable Mirror 2.8.4 Disable Mirror¾ Step 2 Click the Apply button to disable mirroring 2.9 QOS Quality of Service 2.9.1 Get/Refresh the Latest QOS Settings „ Weight„ Scheduling Method „ Priority/Queue Map 2.9.2 Enable QOS ¾ Step 3 Click the Apply button to modify QOS settings 2.9.3 Modify QOS Settings¾ Step 1 Change the Scheduling Method to be Strict Priority 2.10 Rate and Storm Control 2.10.1 Rate ControlPage 2.10.2 Storm Control Page 2.11 System Setup 2.11.1 Firmware Update 2.11.1.1 Firmware Update Via TFTP 2.11.1.2 Firmware Update Via BOOTP/TFTP 2.11.2.1 Assign a fixed IP address 2.11.2 DHCP Client2.11.2.2 Assign an IP address by DHCP server 2.11.3 ARL Aging 2.12 User Management 2.13 Reset System 2.14 Command Line Interface CLI 2.14.1 Hyper Terminal Setup Options2.14.2 Switch Management Commands In Console „ Login System „ Get Current Network Settings „ Help Menu„ Get System Information Press “H”, “h” or “?” to show all management commands in the console „ Configure Network „ User Management „ Enable/Disable 802.1Q VLAN „ Get 802.1Q VLAN Enable Setting„ Set PVID „ Get PVID „ Upgrade Firmware Via TFTP or BOOTP/TFTP „ Reboot System „ Reboot System After Write Default „ LogoutType “RD” or “rd” to reset the system to factory settings Type “LO” or “lo” to logout of the system 3 Specifications „ Standards Compliance„ Interfaces „ Buffer Memory „ Power „ Dimensions„ Weight „ Safety CE Conformity FCC Warning