Manuals
/
Lindy
/
Computer Equipment
/
Switch
Lindy
25010 user manual ¾ Choose Mirror option to be Disable Mirror
Models:
25010
1
38
63
63
Download
63 pages
46.1 Kb
35
36
37
38
39
40
41
42
<
>
Specifications
Dimension
Configurations
Reset System
System Setup
Modify Trunk Settings
Weight
QOS Quality of Service
Firmware Update
Enable/Disable VLAN
Page 38
Image 38
2.8.4 Disable Mirror
¾
Step 1
: Choose Mirror option to be
Disable Mirror
.
¾
Step 2
: Click the
Apply
button to disable mirroring.
37
Page 37
Page 39
Page 38
Image 38
Page 37
Page 39
Contents
English
GIGA Smart Switch 24 +
User Manual
LINDY No
Page
Configurations
Start to Manage This Switch
Configuration Functions for the Switch
Port Configuration
2.11.1.1 Firmware Update Via TFTP
System Setup
Firmware Update
2.11.1.2 Firmware Update Via BOOTP/TFTP
1 Introduction
Main Features
1.1 Start to Manage This Switch
„ IP address
1.2 Configuration Functions for the Switch
2 Configurations
2.1 Port Status
z 2 Options for combo ports Port1 and Port2
2.2 Port Configuration
9 Fibre -Enable, Copper -Enable - to enable both media
z 2 Options for ordinary ports Port3 to Port24, copper media only
¾ 100Mbps Full - to set the speed 100Mbps in full duplex mode
2.3 About the Copper/Fibre Media Auto-Detection
2.4 Port Statistics
UnicastPkts MulticastPkts BroadcastPkts Single Collision
256-511 BytePkts 512-1023 BytePkts 1024-1522 BytePkts FCSErrors
AlignErrors SymbolErrors FragmentPkts OverSizePkts
Multi Collisions 64 BytePkts 65-127 BytePkts 128-255 BytePkts
2.5 Port-Based VLAN
VLAN and 802.1Q VLAN cannot co-exist at the same time
2.5.1 Add Port-Based VLAN Groups
Page
Now all ports are set to the members in VLAN group No.1
2.5.2 Delete Port-Based VLAN Groups
Pressing the Remove This VLAN button results in the following
2.5.3 Edit Port-Based VLAN Groups
2.6 802.1Q VLAN
2.6.1 Enable/Disable VLAN
2.6.2 802.1Q VLAN Port Configuration
2.6.3 802.1Q VLAN Config
The VID entry VID=200 is successfully deleted
Finally, click the Apply button to do the changes
¾ SA + DA both SA and DA
2.7 Trunk
¾ SA Source MAC Address ¾ DA Destination MAC Address
following section will list the related rules for this function
2.7.1 Trunking Rules
Page
2.7.2 Get/Refresh the Latest Trunk Settings
¾ Step 1 Choose the Distribution Criterion
2.7.3 Enable Trunk
¾ Step 3 Click the Apply button to enable trunk settings
¾ Step 2 Choose the member ports up to 8 ports for each trunk group
¾ Step 1 Choose the Distribution Criterion
2.7.4 Modify Trunk Settings
¾ Step 3 Click the Apply button to modify trunk settings
¾ Step 2 Choose the member ports up to 8 ports for each trunk group
¾ Step 1 Click the Not Trunking
2.7.5 Disable Trunk
¾ Step 2 Click the Apply button to disable trunk
2.8 Port Mirroring
2.8.1 Get/Refresh the Latest Mirror Settings
¾ Step 1 Choose Mirror option to be Mirror All Frames
2.8.2 Enable Mirror
¾ Step 4 Click the Apply button to enable mirroring settings
¾ Step 2 Choose the Monitored Port to be Port16
¾ Step 1 Change Mirror option to be Mirror Outgoing Frames
2.8.3 Modify Mirror Settings
¾ Step 4 Click the Apply button to modify mirroring settings
¾ Step 2 Change the Monitored Port to be Port3
¾ Step 2 Click the Apply button to disable mirroring
2.8.4 Disable Mirror
¾ Step 1 Choose Mirror option to be Disable Mirror
2.9 QOS Quality of Service
„ Scheduling Method
2.9.1 Get/Refresh the Latest QOS Settings
„ Weight
„ Priority/Queue Map
2.9.2 Enable QOS
¾ Step 1 Change the Scheduling Method to be Strict Priority
2.9.3 Modify QOS Settings
¾ Step 3 Click the Apply button to modify QOS settings
2.10 Rate and Storm Control
2.10.1 Rate Control
Page
2.10.2 Storm Control
Page
2.11 System Setup
2.11.1 Firmware Update
2.11.1.1 Firmware Update Via TFTP
2.11.1.2 Firmware Update Via BOOTP/TFTP
2.11.2.2 Assign an IP address by DHCP server
2.11.2 DHCP Client
2.11.2.1 Assign a fixed IP address
2.11.3 ARL Aging
2.12 User Management
2.13 Reset System
2.14.2 Switch Management Commands In Console
2.14 Command Line Interface CLI
2.14.1 Hyper Terminal Setup Options
„ Login System
„ Get System Information
„ Get Current Network Settings
„ Help Menu
Press “H”, “h” or “?” to show all management commands in the console
„ Configure Network
„ User Management
„ Set PVID
„ Enable/Disable 802.1Q VLAN
„ Get 802.1Q VLAN Enable Setting
„ Get PVID
„ Upgrade Firmware Via TFTP or BOOTP/TFTP
„ Reboot System
Type “RD” or “rd” to reset the system to factory settings
„ Reboot System After Write Default
„ Logout
Type “LO” or “lo” to logout of the system
„ Interfaces
3 Specifications
„ Standards Compliance
„ Buffer Memory
„ Weight
„ Power
„ Dimensions
„ Safety
CE Conformity
FCC Warning
