Reset System | Lindy 25010 guide

Image 54

Lindy 25010 user manual Reset System

Contents

English GIGA Smart Switch 24 +User Manual LINDY NoPage Configurations Start to Manage This SwitchConfiguration Functions for the Switch Port Configuration 2.11.1.1 Firmware Update Via TFTP System SetupFirmware Update 2.11.1.2 Firmware Update Via BOOTP/TFTP 1 Introduction Main Features 1.1 Start to Manage This Switch „ IP address 1.2 Configuration Functions for the Switch 2 Configurations 2.1 Port Status z 2 Options for combo ports Port1 and Port2 2.2 Port Configuration9 Fibre -Enable, Copper -Enable - to enable both media z 2 Options for ordinary ports Port3 to Port24, copper media only ¾ 100Mbps Full - to set the speed 100Mbps in full duplex mode 2.3 About the Copper/Fibre Media Auto-Detection 2.4 Port Statistics UnicastPkts MulticastPkts BroadcastPkts Single Collision 256-511 BytePkts 512-1023 BytePkts 1024-1522 BytePkts FCSErrorsAlignErrors SymbolErrors FragmentPkts OverSizePkts Multi Collisions 64 BytePkts 65-127 BytePkts 128-255 BytePkts 2.5 Port-Based VLAN VLAN and 802.1Q VLAN cannot co-exist at the same time 2.5.1 Add Port-Based VLAN Groups Page 2.5.2 Delete Port-Based VLAN Groups Pressing the Remove This VLAN button results in the followingNow all ports are set to the members in VLAN group No.1 2.5.3 Edit Port-Based VLAN Groups 2.6 802.1Q VLAN 2.6.1 Enable/Disable VLAN 2.6.2 802.1Q VLAN Port Configuration 2.6.3 802.1Q VLAN Config The VID entry VID=200 is successfully deleted Finally, click the Apply button to do the changes 2.7 Trunk ¾ SA Source MAC Address ¾ DA Destination MAC Address¾ SA + DA both SA and DA following section will list the related rules for this function 2.7.1 Trunking Rules Page 2.7.2 Get/Refresh the Latest Trunk Settings ¾ Step 1 Choose the Distribution Criterion 2.7.3 Enable Trunk¾ Step 3 Click the Apply button to enable trunk settings ¾ Step 2 Choose the member ports up to 8 ports for each trunk group 2.7.4 Modify Trunk Settings ¾ Step 3 Click the Apply button to modify trunk settings 2.7.5 Disable Trunk ¾ Step 2 Click the Apply button to disable trunk¾ Step 1 Click the Not Trunking 2.8 Port Mirroring 2.8.1 Get/Refresh the Latest Mirror Settings ¾ Step 1 Choose Mirror option to be Mirror All Frames 2.8.2 Enable Mirror¾ Step 4 Click the Apply button to enable mirroring settings ¾ Step 2 Choose the Monitored Port to be Port16 ¾ Step 1 Change Mirror option to be Mirror Outgoing Frames 2.8.3 Modify Mirror Settings¾ Step 4 Click the Apply button to modify mirroring settings ¾ Step 2 Change the Monitored Port to be Port3 2.8.4 Disable Mirror ¾ Step 1 Choose Mirror option to be Disable Mirror¾ Step 2 Click the Apply button to disable mirroring 2.9 QOS Quality of Service „ Scheduling Method 2.9.1 Get/Refresh the Latest QOS Settings„ Weight „ Priority/Queue Map 2.9.2 Enable QOS 2.9.3 Modify QOS Settings ¾ Step 3 Click the Apply button to modify QOS settings¾ Step 1 Change the Scheduling Method to be Strict Priority 2.10 Rate and Storm Control 2.10.1 Rate ControlPage 2.10.2 Storm Control Page 2.11 System Setup 2.11.1 Firmware Update 2.11.1.1 Firmware Update Via TFTP 2.11.1.2 Firmware Update Via BOOTP/TFTP 2.11.2 DHCP Client 2.11.2.1 Assign a fixed IP address2.11.2.2 Assign an IP address by DHCP server 2.11.3 ARL Aging 2.12 User Management 2.13 Reset System 2.14.2 Switch Management Commands In Console 2.14 Command Line Interface CLI2.14.1 Hyper Terminal Setup Options „ Login System „ Get System Information „ Get Current Network Settings„ Help Menu Press “H”, “h” or “?” to show all management commands in the console „ Configure Network „ User Management „ Set PVID „ Enable/Disable 802.1Q VLAN„ Get 802.1Q VLAN Enable Setting „ Get PVID „ Upgrade Firmware Via TFTP or BOOTP/TFTP „ Reboot System Type “RD” or “rd” to reset the system to factory settings „ Reboot System After Write Default„ Logout Type “LO” or “lo” to logout of the system „ Interfaces 3 Specifications„ Standards Compliance „ Buffer Memory „ Weight „ Power„ Dimensions „ Safety CE Conformity FCC Warning