Linear AE1000Plus Pbus Accessories, Wiegand Accessories, Wiegand Terminals

PBUS Accessories

Up to six accessories (keypads, proximity readers, remote receivers) can be connected to the three PBUS input/output ports. A typical application for a remote keypad would be to control a second door or gate.

Linear’s PBUS devices compatible with the AE1000Plus are:

•AM-RRR Remote Radio Receiver

•AM-RGR Remote Radio Receiver

•AM-RPR Radio Proximity Receiver

•AM-KP Exterior Keypad

•AM-KPI Interior Keypad

•AM-CRI Card Reader Interface

Conventional cable or commonly available Cat-5e Ethernet cable can be used to connect PBUS remote devices to the AE1000Plus. When using Cat-5e cable, note that the PWR and GND connections use two wires each to enhance the current carrying capacity for powering the remote device.

Cable choices:

•Cat-5e Ethernet cable for wire runs up to 500'.

•24 AWG Belden Type 9931 or equivalent for wire runs up to 300'.

•20 AWG Weico Type 9405 or equivalent for wire runs up to 600'.

1.Mount and install the accessory as described in its instructions.

2.Route cable from the AE1000Plus to the accessory.

3.Set the DEVICE ADDRESS rotary switch in the accessory to a unique address number. When programming the system, the device address number will identify each PBUS accessory to the AE1000Plus.

4.Connect the cable to the accessory and the AE1000Plus (see PBUS wiring diagram).

		PWR		PWR
REMOTE		GND		GND
		DAT1		DAT1	PBUS
	PBUS
		DAT0		DAT0	TERMINALS
	DEVICE
		DVAL		DVAL
		PCLK		PCLK
	NOTE: UP TO SIX PBUS DEVICES MAY BE CONNECTED
	TO THE THREE SETS OF PBUS TERMINALS
	ORANGE &		CAT-5e WIRING EXAMPLE	ORANGE &
	ORANGE-WHITE			ORANGE-WHITE
BROWN &						BROWN &
BROWN-WHITE					BROWN-WHITE
PWR						PWR
GND	GREEN-WHITE			GREEN-WHITE		GND
DAT1						DAT1
	GREEN				GREEN
DAT0						DAT0
DVAL	BLUE				BLUE	DVAL
PCLK	BLUE-WHITE			BLUE-WHITE		PCLK
REMOTE PBUS					ACCESS
DEVICE TERMINALS			CAT-5e	CONTROL SYSTEM
				PBUS TERMINALS
			4-UTP CABLE
			UP TO 500 FEET PER DEVICE

Wiegand Accessories

The two AE1000Plus Wiegand inputs (WIEGAND A & B) can connect to a large variety of 26, 30, and 31-bit Wiegand output accessories. The Wiegand format is a common standard for access control equipment. A typical application would be to add swipe card or proximity readers to the system.

✦NOTE: Depending on the Wiegand accessory used, the LED1, LED2, and HOLD connections may not be required.

•LED1 output is switched to ground during non-access time.

•LED2 output is switched to ground for one second during access time.

1.Mount and install the Wiegand accessory as described in its installation instructions.

2.Route a cable from the AE1000Plus to the accessory.

•For wire runs up to 300 feet use 24 AWG Belden Type 9931 or equivalent.

•For wire runs up to 500 feet use 20 AWG Weico Type 9405 or equivalent.

LED2

HOLD REMOTE LED1 WIEGAND DAT1 DEVICE DAT0 GND PWR

WIEGAND

TERMINALS

LED2

HOLD

LED1

DAT1

DAT0

GND

PWR

3.Connect the cable to the accessory and the AE1000Plus as shown in the fi gure.

NOTE: THE LED1, LED2, AND HOLD CONNECTIONS MAY NOT BE REQUIRED DEPENDING ON THE WIEGAND DEVICE USED

14