TROUBLESHOOTING GUIDE

TROUBLESHOOTING GUIDE

 

PROBLEM

POSSIBLE CAUSE

CORRECTIVE ACTION

 

 

 

 

 

 

 

 

 

 

 

 

A.

Engine will not start

1.

Out of gasoline.

1.

Fill gasoline tank.

 

 

 

 

 

2.

Spark plug lead wire loose

2.

Reconnect spark plug lead wire.

 

 

 

 

 

 

or disconnected.

 

 

 

 

 

 

 

 

3.

Defective spark plug.

3.

Replace spark plug.

 

 

 

 

 

4.

Throttle control lever not

4.

Move throttle control lever to start position.

 

 

 

 

 

 

in proper position.

 

 

 

 

 

 

 

 

5.

Engine flooded or flooding.

5.

Start engine with choke fully open.

 

 

 

 

 

6.

Stale or contaminated

6

Drain, clean tank and system and refill with

 

 

 

 

 

 

gasoline.

 

fresh gasoline.

 

 

 

 

 

7.

Engine switch off.

7.

Turn engine switch to ON position.

 

 

 

 

 

8.

Oil level low.

8.

Fill crankcase to proper oil level.

 

 

 

 

 

 

 

 

 

 

B. Loss of power, hard

1.

Spark plug lead wire loose.

1.

Tighten spark plug lead wire.

 

 

 

 

starting.

2.

Defective spark plug.

2.

Replace spark plug.

 

 

 

 

 

3.

Carburetor out of adjustment.

3.

Properly adjust carburetor.

 

 

 

 

 

4.

Air cleaner dirty.

4.

Clean and service air cleaner. (See the Honda

 

 

 

 

 

 

 

 

Operation and Maintenance illustrations.)

 

 

 

 

 

5.

Air vents clogged or plugged.

5.

Clean vent in gasoline tank cap and carburetor.

 

 

 

 

 

 

 

 

 

 

 

C. Engine will not idle

1.

Idle speed too slow.

1.

Adjust carburetor idle speed or idle mixture.

 

 

 

 

properly.

2.

Spark plug gap incorrect.

2.

Set spark plug gap .030 (.76mm) for Honda

 

 

 

 

 

3.

Air cleaner dirty.

 

engine.

 

 

 

 

 

 

 

3.

Clean and service air cleaner. (See the Honda

 

 

 

 

 

 

 

 

Operation and Maintenance illustrations.)

 

 

 

 

 

 

 

 

 

 

D. Engine runs hot or

1.

Oil level low.

1.

Fill crankcase to proper oil level.

 

 

 

 

overheats.

2.

Engine cooling fins or baffles

2.

Clean and remove obstructions.

 

 

 

 

 

 

clogged with dirt and debris.

 

 

 

 

 

 

 

 

3.

Carburetor out of adjustment.

3.

Readjust carburetor.

 

 

 

 

 

 

 

 

 

 

 

E.

Control mechanisms

1.

Parts bent, distorted, worn

1.

Inspect control mechanism and repair

 

 

 

 

for depth of blade

 

out or missing.

 

or replace damaged, worn out, or missing

 

 

 

 

will not function.

 

 

 

components.

 

 

 

 

 

 

 

 

 

 

 

WARNING - ALL LITTLE WONDER EDGERS ARE SHIPPED WITHOUT OIL. WHEN FILLING OIL -

Use SAE 30 Oil. REFER TO ENGINE MANUFACTURES INSTRUCTION MANUAL

FOR PROPER ENGINE OPERATION INSTRUCTIONS

11

Page 11
Image 11
Little Wonder 6232 manual Troubleshooting Guide, Problem, Possible Cause, Corrective Action