Manuals / Brands / Computer Equipment / Network Card / LSI / Computer Equipment / Network Card

LSI 20160 2.2.4.2 Making Activity LED Connection, Figure 2.7 Multiple Internal SCSI Devices Chained Together

1 62

Download 62 pages, 425.07 Kb

Figure 2.7 Multiple Internal SCSI Devices Chained Together2.2.4.2 Making Activity LED Connection

Most PC cabinets are designed with a front panel LED to indicate bus activity. It may already be connected to an existing IDE controller. If you want, you can connect the LED to the SCSI LED connector.

Connect the LED cable to J3 on your SCSI host adapter, as shown in Figure 2.8.

The Busy LED connector J3 is not keyed. The J3 connector is a 4-pin one row right angle header. Some LED cables have only two wires. In this case, place the connector on one end of J3. If the LED does not light during SCSI bus activity, you may have to rotate the LED cable 180˚ on J3 or move it to the other end of the jack.

2-10	Installing the LSI20160

Copyright © 2001 by LSI Logic Corporation. All rights reserved.

Contents

USER’S GUIDE Electromagnetic Compatibility Notices Page Page Preface Related Publications Revision History Contents Appendix A Glossary of Terms and Abbreviations Customer Feedback Figures Page Tables Page Describing the LSI20160 1.1General Description 1.2 Features 1.2.1 PCI Interface 1.2.2 SCSI Interface 1.2.3 Board Characteristics 1.2.4SCSI Activity LED Interface 1.3 Ultra160 SCSI Beneﬁts 1.3.1 Double Transition (DT) Clocking 1.3.2 Cyclic Redundancy Check (CRC) 1.3.3 Asynchronous Information Protection (AIP) 1.4 SureLINK™ Ultra160 SCSI Domain Validation Beneﬁts 1.5 LVDlink™ Technology Beneﬁts 1.6 TolerANT® Technology Beneﬁts Installing the LSI20160 2.1Quick Installation Procedure 2.2 Detailed Installation Procedure 2.2.1 Before You Start 2.2.2 Selecting a PCI Slot 2.2.3 Inserting the Host Adapter Figure 2.2 Inserting the Host Adapter 2.2.4 Connecting SCSI Peripherals 2.2.4.1 Making Internal SCSI Bus Connections Figure 2.4 Internal SCSI Ribbon Cable to Host Adapter Figure 2.5 Internal SCSI Ribbon Cable to Internal SCSI Device Connection Figure 2.6 Connecting Additional Internal SCSI Devices Figure 2.7 Multiple Internal SCSI Devices Chained Together 2.2.4.2 Making Activity LED Connection Figure 2.8 SCSI LED Connector 2.2.4.3 Making External SCSI Bus Connections Figure 2.9 External Cable to Host Adapter Figure 2.10 External Cable to External SCSI Device Figure 2.11 Multiple External SCSI Devices Chained Together 2.2.5 SCSI Bus Termination 2.2.5.1 Internal SCSI Terminations Figure 2.12 Internal SCSI Device Termination 2.2.5.2 External SCSI Terminations Figure 2.13 External SCSI Device Termination 2.2.6 Setting SCSI IDs Table 2.1 SCSI ID Record 2.3 Completing the Installation Technical Speciﬁcations 3.1Physical Environment 3.1.1 Physical Characteristics 3.1.2Electrical Characteristics 3.1.3 Thermal, Atmospheric Characteristics 3.1.4Electromagnetic Compliance 3.1.5 Safety Characteristics 3.2 Operational Environment 3.2.1 The PCI Interface Table 3.2 PCI Connector J1 (Front)1 Table 3.3 PCI Connector J1 (Back)1 3.2.2 The SCSI Interface 3.2.3 The LED Interface 3.3 Subsystem ID and Subsystem Vendor ID Page Appendix A Glossary of Terms and Abbreviations Bus Mastering Byte CISPR Conﬁguration CRC Dword EEPROM EISA External SCSI Device IRQ ISA Kbyte Local Bus Logical Unit NVRAM Operating System Parity Checking Passive PC99 RAM RISC Core ROM SCAM SCSI SCRIPTS Processor SDMS Single-Ended STA SureLINK Ultra160 SCSI VCCI VDE VHDCI Virtual Memory Index Page Customer Feedback Reader’s Comments http://www.lsilogic.com/contacts/na_salesofﬁces.html