U

GAIN

-20dB +20dB 23

SEND INPUT

LINE

UFW 1-2

HIGH

12kHz

-15 +15

U

MID

2.5kHz

-15 +15

CTRL ROOM/PHONES

 

 

 

46. POWER LED

SOURCE

0dB=0dBu

 

This green LED will turn on when the mixer is turned

 

L

R

 

35

 

on, as a reminder of how on it really is. If it is not on,

20

CLIP

 

MAIN MIX

15

 

 

then it is off, and the mixer becomes a rather nice

 

10

 

 

weight for keeping your morning newspaper from

TAPE 36

6

 

 

blowing away in the wind.

3

 

 

 

 

 

 

If it does not turn on, make sure the power cord is

 

0

 

 

FW 1-2 ALT 3-4

2

LEVELSET

40

correctly inserted at both ends, the local AC mains

 

4

supply is active, and the power switch [2] is on.

37

 

 

7

 

 

 

 

 

 

 

ASSIGN TO

10

 

 

Talkback

MAIN MIX

20

 

 

 

 

 

 

 

 

 

 

30

 

 

 

U

LOW

80Hz

-15 +15

AUX

1

OO

MAX

 

2

OO

MAX

 

PAN

L R

OO

MAX

 

OO

MAX

RUDE

 

 

 

CONTROL

PHONES

SOLO

ROOM

 

 

39

 

 

 

41

38

 

 

 

 

 

 

AUX MASTER

 

43

SEND

45

RETURN

 

 

 

 

1

 

1

PRE

OO

 

+15

 

OO

+10

 

 

AUX1

POST

 

42

 

44

 

 

RTN TO

 

 

 

 

 

 

2

 

2

PRE

OO

 

+15

 

OO

+10

POST

 

 

 

 

 

 

 

 

46

POWER

The talkback feature allows the engineer to communicate with the talent either through the phones outputs [17] or the aux 1-2 send outputs [6] using the built-in talkback microphone. This saves a lot of shouting over the audience's heads as you set up the talented one's stage monitors to their peculiarly-picky satisfaction.

47. TALKBACK MIC

This is where the built-in talkback microphone is located. It is an omni-directional dynamic microphone, and it will pick up your voice from anywhere in front of the mixer.

MUTE

 

 

ALT 3/4

47

 

 

 

dB

MIC

 

 

10

 

 

5

48

 

OL

 

U

 

 

5

OO

MAX

- 20

LEVEL

10

 

 

20

DESTINATION

49

 

30

 

 

 

40

PHONES

AUX

 

1-2

50

 

 

 

60

 

 

OO

 

 

50

TALKBACK

SOLO

11-12TALKBACK

51

dB 10

5

U

5

10

20

30

40

50

60

OO

MAIN MIX

48. TALKBACK LEVEL

Use this knob to control the level of the talkback signal being routed to the phones or aux 1-2 outputs, from the internal microphone.

1.Start with this control turned down.

2.Select the destination, either headphones and/or aux 1-2, and make sure their levels are already set nicely, such as phones [39] or aux sends [42].

3.Hold down the talkback switch [50] as you make your fruity-toned announcements.

4.Slowly turn this talkback level control up until you get confirmation from whoever is listening to headphones or monitors that they can hear and obey your every command.

Once you have set the level, you can leave it there for the duration of the session or gig.

49. DESTINATION: PHONES, AUX 1-2

Push in the phones switch to route the talkback signal to the headphones. Use this to communicate with the talent in the studio through the headphones during a recording session. When the talkback circuit is activated by pushing the talkback [50] switch, the control room outputs [12] are attenuated to allow your voice to come through clearly.

Owner's Manual 25