Putting Batteries in the Remote Control | Magnavox CCX133AT99

Before Using the TV/VCR 5

Putting Batteries in the Remote Control

1

Remove the battery compartment lid on the bottom of the remote control by sliding it in the direction of the arrow.

2

Place two AA batteries inside the battery compartment with their polarities (+ and – ends) aligned as indicated.

3

Replace the battery compartment lid.

Removing the Shipping Card

●A shipping card may be inserted in the cassette compartment of the TV/VCR. Before you insert a cassette tape, you must remove the shipping card. To remove the card, open the cas- sette compartment, then grasp the tape and remove the card.

Erase Protection

Video cassette tapes have record tabs to ensure that recordings are not accidentally erased.

1

To prevent accidental erasure, break off the tab with a screwdriver.

2

To record again, cover the hole with cellophane tape.

Using the Remote Control

●Point the remote control at the TV/VCR’s remote sensor.

●Do not put objects between the remote control and the TV/VCR.

1

2

3

1

2

VCR Maintenance

●In this TV/VCR, use only tapes with the mark.

●Make sure any light adhesive stick-on notes are removed from the video cassette tape before putting the tape in the TV/VCR. Removable labels like these can jam the TV/VCR.

●Periodic maintenance is required to maintain your TV/VCR’s continued excellent performance. This TV/VCR has an automatic head cleaning system. However, the video heads will eventually require cleaning or replacement. Cleaning or replacement of the video heads should be performed by an authorized service cen- ter.

Helpful Hints

•The remote control and its batteries are supplied.

•Do not mix alkaline and man- ganese batteries.

•Do not mix old and new batteries.

Image 5

Magnavox CCX133AT99 Putting Batteries in the Remote Control, Removing the Shipping Card, Erase Protection, VCR Maintenance

Contents

CCX133AT For Customer Use Dear Philips Magnavox product owner Introduction FeaturesSafety Precautions Table of Contents Using the Remote Control Putting Batteries in the Remote ControlVCR Maintenance Removing the Shipping Card Rod Antenna Hook up your TV/VCR using one of the connections shownHooking Up The TV/VCR Bent pin Hooking Up The TV/VCR cont’dCrooked Pin Straight Pin Cable Plug Turning On the TV/VCR Press the Menu button to display the pop up menu Language Selection Channel Memory Press the Number 3 button to select ADD/DELETE Channel Adding/Deleting ChannelsEnter the channel number you want to add or delete Press the Menu button Manual Clock Setting Setting the ClockChannels are programmed. Details are on pages 10 Press the Number 6 button to select SET Clock Press the Number 2 button to select SET Manual Clock Setting the Clock cont’d Press the Menu button to display the pop up menu Setting the Clock cont’dAutomatic PBS Channel Selection Press the Number 1 button to select SET PBS CH Wait for the TV/VCR to findTime Manual PBS Channel Selection NOW Searching flashes on the TV/VCR screen Find the timeUse the Number buttons to select your PBS station Press the PLAY/ button or the STOP/ button to select Daylight-Saving Time You cannot select Time Zone at if Auto Clock is set to OFF Time ZonePress the Number 4 button to select SET Time Zone Front Panel ANTenna Jack Rear PanelConnect your antenna or cable here Details are on pages six seven Remote Control Buttons ALT. CH Alternate Channel Button Volume Up/Down ButtonsChannel Up/Down Buttons Mute Button Adjusting the Picture Controls Press the REWind/- button to decrease a picture control Decrease IncreaseDecreased brightness On-Screen Status Displays On Mode Reminder Playing Speed are given below RecordingPress the RECord/OTR button once to start recording Recording options are on pages 30 You can not pause an OTR One Touch RecordingOTR Audio and video cables are not included Rerecording Tape DuplicationDifferent brands of equipment may operate differently Select a once, daily or weekly recording Timer Recording Timer Recording cont’d Timer Recording cont’d Checking or Clearing Timer Recordings Local TV Stations Call letters Setting Up the VCR Plus+ Programming SystemTV Channels Cable Channels Press the STATUS/EXIT button to exit Examine the lists onPress the Number 5 button to select VCR PLUS+ REF. MAP Screen display shown below will appear Press the VCR PLUS+ button on the remote control. The on Timer Recording With the VCR Plus+ Programming System cont’d Follow the steps below to prevent accidental recording Record DefeatRecord Defeat If the power fails, you might lose the sleep timer setting Setting the Sleep Timer Example Closed CaptioningMenu Screen Text Screen Closed Captioning cont’dStandard Closed Captioning Volume Bar Volume Bar / Smart SoundTo turn Volume Bar On or Off Smart Sound Repeat Playback Insert a tape in the TV/VCR B Repeat Playback Repeat Playback cont’d Real Time Counter Memory Button to reset the real time counter to zeroAppear on-screen While the counter remains on-screen, press the Clear Automatic Operation Features Forward and Reverse Searching SP/LP/SLP Playback OptionsSuper High Speed Searching LP/SLP Viewing a Still Picture Glossary Specifications Helpful Hints Helpful Hints cont’d Renewed Index Supplied Accessories