Manhattan Computer Products XT-F Editing TP in Channel Search Menu, Trouble Shooting Guide

EDITING TP IN CHANNEL SEARCH MENU

Press MENU, go to INSTALL and select Channel Search. Configure following items.

Adding TP

Satellite: Press OK and select satellite. Press right key and go to Scan Mode and select Manual TP / All Ch. TP Data will open. Press left / right and select User TP 1. Enter, Frequency, Polarity and S/R. Press EXIT and TP Data will close. Added TP is already selected for channel search. Press blue key. After tuning it will store the TP. To add another TP select User TP 2.

Editing TP

Same as adding but select the required TP and edit its data.

TROUBLE SHOOTING GUIDE

If you suspect there is a problem with your STB, please check the following.

WARNING! Do not attempt to repair the STB yourself. Tampering with the receiver may result in fatal electric shock and will invalidate your warranty.

Front display not lit --- Check power lead is connected and the power is on.

No picture or sound --- Check TV is tuned for correct UHF channel or is switched to correct AV input. Channel is scrambled.

No signal --- Check antenna position. Check LNB wire is not damaged or shorting. Check LNB may be faulty. Unplug receiver from power socket and retry.

Interference, on picture, using UHF output --- Local terrestrial channel interference. Change UHF output channel to different one and re-tune your TV. Select the appropriate ‘TV Standard’ using TV Settings menu.

Picture with blocking or frozen --- Signal is weak. Check signal & quality in Channel Search menu. Check antenna position.

Remote control not working --- Check the batteries and replace with new. Check front panel of STB is not obstructed.

You have lost or forgotten your password --- Apply master password or contact your Manhattan dealer.

GENERAL SPECIFICATIONS
Conditional Access Interface
Smart Card Reader	2 Embedded Card Slots
PCMCIA	1 Common Interface (CI) Slot
Digital Tuner & Demodulator
Input Connector	F-Type, IEC, 169-24, Female
Input Frequency & Loop	950 MHz to 2150 MHz
through range
Input Impedance	75 ohm unbalanced
Signal Level	-25 to –65 dBm

LNB Power & Polarization	Vertical + 13V, Horizontal + 18V, Max Current 500 mA,
	Short Circuit Protection
22KHz Tone	Frequency 22 KHz +/- 2 KHz, Amplitude 0.7 +/- 0.2V
DiSEqC Control	Version 1.0, 1.2 & USALS
Demodulation	QPSK
Input Symbol Rate	1-45 Ms/s, SCPC & MCPC
FEC Decoder	Convolutional Code Rate, 1/2, 2/3, 3/4, 5/6 and 7/8
	with constraint length K=7
System Memory
Main Core Processor	ST-5119 @ 200 MHz
Flash Memory	2MB
SDRAM	16MB
EEPROM	8KB
Channel Memory	6000 Channels
Language Menu	English, French, German, Spanish, Italian, Portuguese,
	Danish, Swedish, Norwegian, Finish, Polish, Russian,
	Greek, Turkish, Farsi & Arabic
MPEG Transport Stream, A/V Decoding
Transport Stream	MPEG-2 ISO/IEC 13818
Profile Level	Transport Stream Specification MPEG-2 MP@ML
Input Rate	Max. 90 Mbit/s
Aspect Ratio	4:3 Letter Box, 4:3 Pan & Scan, 16:9 Wide
Video Resolution	720X576 @ 25Hz, 720X480 @ 30Hz
Audio Decoding	MPEG/Musicam Layer I & II
Audio Mode	Single Channel, Dual Channel, Joint Stereo & Stereo
Sampling Rate	16, 22.05, 24, 32, 44.1 and 48 KHz
Digital Audio	S/PDIF
A/V & Data In / Out
TV SCART	Video Output (CVBS, RGB). Audio output with Volume
	Control (Resolution: 20 bits DAC, Max 2Vrms)
VCR SCART	Video Output (CVBS) Video Input (CVBS) Audio Output
	(Resolution: 20bits DAC Max.1Vrms)
Video	RCA / Cinch, Video Output (CVBS)
Audio R/L	RCA/Cinch Volume & Mute Control
S/PDIF	Digital audio Output, RCA (Resolution: 20 bits)
RS-232	Transfer rate 115.2 Kbps 9 Pin D-sub type
RF-Modulator (OPTIONAL)
RF-Connector	75 Ohm, IEC 169-2 Male/Female
Frequency	470 to 850 MHz
Output Channel	CH 21 – 69 for the re-modulator
Multi TV Standards	PAL G, I, K, M & NTSC M
Preset Channel	CH 64 (software changeable by Menu)
Power Supply
Input Voltage	90 to 240 VAC, 50/60 Hz
Type	SMPS
Power Consumption	Max 25W
Standby	7.2W

15 16