ENGLISH |
Introduction
Introduction | Part Names and Functions |
|
| ||
Front Panel |
|
|
| ||
7 | 8 | 9 | 10 11 12 | ||
| |||||
Introduction
Rear Panel
1 | 2 | 3 | 4 | 5 | 6 |
Connections |
|
|
|
1 2 | 3 4 | 5 | 6 |
AC IN | DIGITAL OUT COMPONENT VIDEO OUT VIDEO OUT | FLASHER |
IN OUT
| COAXIAL |
NETWORK | HDMI OUT |
7 | 8 |
2ch AUDIO OUT
R 
L
Playback | The unit can also be turned on by pressing the buttons with circled numbers. | |||
| ||||
| 1. | STANDBY indicator | 8. | A (OPEN/CLOSE) button |
|
| This indicator lights up in red in standby |
| Press to open or close the disc tray. |
|
| mode and turns off when the power is on. | 9. | Disc tray |
| 2. | POWER ON/STANDBY button |
| Place a disc when opening the disc tray. |
|
| Press to turn on the unit, or to turn the unit | 10. B (PLAY) button | |
Function |
| |||
| unplug the AC cord.) | 12. F (STILL/PAUSE) button | ||
|
| to the standby mode. (In standby mode, this |
| Press to start or resume playback. |
|
| unit still consumes small amount of power. | 11. C (STOP) button | |
|
| To completely shut down the unit, you must |
| Press to stop playback. |
|
|
|
| |
Setup | 3. | HDMI RESOLUTION button |
| Press to pause playback. |
| Press to set the HDMI jack’s video signal |
| ||
|
|
| ||
|
|
|
| |
|
| output mode. |
|
|
| 4. | Infrared sensor window |
|
|
|
| Receives signals from your remote control so |
|
|
|
| that you can control the unit from a distance. |
|
|
Others | 5. | Display |
|
|
| Refer to “Front Panel Display” on page 9. |
|
| |
| 6. | SD card slot |
|
|
|
| Insert an SD Memory Card, and play back the |
|
|
|
| contents in it. |
|
|
| 7. | H / G (SKIP DOWN/UP) button |
|
|
|
| Press to skip down/up titles/chapters/tracks/ |
|
|
|
|
|
| |
|
| files. |
|
|
1.AC IN Terminal
Use to connect the AC cord to supply the power.
2.DIGITAL OUT (COAXIAL) jack
Use digital audio coaxial cable to connect to an AV receiver, Dolby Digital decoder or other device with a digital audio coaxial input jack.
3.COMPONENT VIDEO OUT jacks
Use a component video cable to connect to a display device with component input jacks.
4.VIDEO OUT jack
Use an RCA video cable to connect to a TV monitor, AV receiver or other device.
5.FLASHER IN / OUT jacks
This Input terminal is equipped for controlling this unit by the external Infrared (IR) control device. Connect the IR control signal from a Keypad, IR repeater, etc. The Output terminal repeats the IR signal which was fed into the IR Flasher Input terminal for another device.
6.2ch AUDIO OUT jacks
Use an RCA audio cable to connect these jacks to the
7.NETWORK Terminal
Use to connect a telecommunications equipment with LAN cable.
8.HDMI OUT jack
Use an HDMI cable to connect to a display with an HDMI input jack.
Note
•Do not touch the inner pins of the jacks on the rear panel. Electrostatic discharge may cause permanent damage to the unit.
7
ENGLISH
