Marantz SR3001 manual Other Function, Listening Through Headphones, Display Mode, Video ON/OFF

OTHER FUNCTION

ATTENUATION TO ANALOG INPUT SIGNAL

BASS TREBLE TUNE/SEARCH

T-MODE RDS F.DIRECT

SURROUND

DIGITAL

AAC

INPUT/DISC+ AUDIO SUB-T/ATTPTY

CH.SEL LIP.SYNC

SYSTEM REMOTE CONTROLLER

RC5500SR

LISTENING THROUGH HEADPHONES

This jack may be used to listen to the SR3001’s output through a pair of headphones. Be certain that the headphones have a standard 1/4" stereo phono plug. (Note that the speakers will automatically be turned off when the headphone jack is in use.)

AV SURROUND RECEIVER SR3001

DISPLAY MODE

AV SURROUND RECEIVER SR3001

SET UP/		MENU OFF
T.TONE
PURE DIRECT	AUTO		DTS
SURROUND	1	2	3
DIGITAL
AAC
NIGHT	CSII	EX/ES	VIRTUAL
	4	5	6
DISPLAY	MCH-ST	STEREO	7.1CH IN
	7	8	9
CLEAR	MEMO	A/D	P.SCAN/V-OFF
		0
		CHANNEL/SKIP
BASS	TREBLE	TUNE/SEARCH
	T-MODE	RDS	F.DIRECT

You can select the display mode for the front display of the SR3001.

To select this mode, press the DISPLAY on the front panel or on the remote.

SELECTING ANALOG AUDIO INPUT OR

DIGITAL AUDIO INPUT

SET UP/		MENU OFF
T.TONE
PURE DIRECT	AUTO		DTS
	1	2	3
NIGHT	CSII	EX/ES	VIRTUAL
	4	5	6
DISPLAY	MCH-ST	STEREO	7.1CH IN

7 8 9

CLEAR MEMO A/D P.SCAN/V-OFF

0

CHANNEL/SKIP

BASS TREBLE TUNE/SEARCH

T-MODE RDS F.DIRECT

If you have already assigned the digital inputs, you can temporarily select the audio input mode for each input source with the A/D button on the remote

ENGLISH

If the selected analog audio input signal is greater than the capable level of internal processing, the “PEAK” indicator will light up on the front display. If this happens, you should press the ATT button on the front panel or on the remote.

“ATT” indicator will be illuminated when this function is activated. The signal-input level is reduced by about half. Attenuation will not work with the output signal of TAPE-OUT, CD-R/MD-OUT, VCR1-OUT and DSS/ VCR2-OUT.

This function is memorized for each individual input source.

Notes:

•When using headphones, the surround mode will change to STEREO and TruSurround (TS) headphones by SURROUND MODE button.

•The surround mode returns to the previous setting as soon as the plug is removed from the jack.

VIDEO ON/OFF

When no video signal is connected to the SR3001 or a DVD, etc., is connected directly to your TV, the unnecessary video circuit can be turned off by selecting the “VIDEO OFF” setting.

To select video off, press the V-OFFbutton on the remote.

T.TONE
PURE DIRECT	AUTO		DTS
	1	2	3
NIGHT	CSII	EX/ES	VIRTUAL
	4	5	6
DISPLAY	MCH-ST	STEREO	7.1CH IN
	7	8	9

CLEAR MEMO A/D P.SCAN/V-OFF

		0
		CHANNEL/SKIP
BASS	TREBLE	TUNE/SEARCH
	T-MODE	RDS	F.DIRECT
INPUT/DISC+	AUDIO	SUB-T/ATT	PTY
CH.SEL			LIP.SYNC

When this button is pressed, the display mode is switched in the following sequence.

→Surround Mode → Auto-display Off → Display Off

→Input Function → Surround Mode....

In Auto display off mode, the display is off. But, if you make a change to the unit such as input or surround mode, the display will show that change, then go back to off after about 3 seconds. When changing the volume, it is not displayed.

In Display off mode, the display is off completely.

Note:

Only the DISP indicator will be illuminated on the front display, in display off condition

controller.

When this button is pressed, the input mode is switched in the following sequence.

→Digital Auto → Digital → Analog → Digital Auto....

In Digital Auto mode, the types of signals being input to the digital and analog input jacks for the selected input source are detected automatically.

If no digital signal is being input, the analog input jacks are selected automatically.

In Digital mode, input is fixed to an assigned digital input terminal.

In analog mode, the analog input jacks are selected. This selecting is temporary, so the result will not be stored in memory.

If you need to change the input mode completely, use INPUT setup in SETUP MENU system. (see page 17)

27