Marantz SR5400U manual Remote Control Operation, Function and Operation

REMOTE CONTROL

OPERATION

FUNCTION AND OPERATION

The provided remote control unit is a universal re- mote controller. The POWER button, numeric but- tons and control buttons are used in common across different input source components.

The input source controlled with the remote control unit changes when one of the input selector but- tons is pressed.

	POWER				z
					x
	TV	VCR1	DSS/VCR2	DVD
	TUNER	CD	TAPE	CDR/MD	c
		AUX	AMP
¤4	TV			MAIN	v
	VOL.	SLEEP	MUTE	VOL.
¤3					b
¤2	OSD		MENU		n
		OK			m
¤1	SETUP/		MENU OFF		,
¤0	T.TONE
	S-DIRECT	AUTO		DTS
⁄9		1	2	3
	NIGHT	CSII	EX/ES	DSP
		4	5	6
⁄8	DISPLAY	M-CH ST STEREO		6.1CH IN.
⁄7		7	8	9	⁄0
	CLEAR	MEMO	A/D	P.SCAN
⁄6			0		⁄1
			CHANNEL/SKIP
⁄5	BASS	TREBLE	TUNE/SEARCH
⁄4		MODE	DISP./RDS F.DIRECT		⁄2
	+/A /ANT	–/B /VCR	ATT.	PTY
	DISC/DECK				⁄3

SYSTEM REMOTE CONTROLLER

RC5400SR

zTransmitting indicator

Lights up during a button is pressed and an infrared signal is sending.

x(Main) POWER buttons

(when AMP mode is selected)

Press to switch the power of the SR5400 ON or OFF after pressing the AMP button.

cInput selector buttons/ FUNCTION

SELECTOR buttons (AUDIO/VIDEO INPUT)

These buttons are used to select a Audio or Video source component. Press one of these buttons once to change the function of the remote control. Press same button within 2 seconds, the input func- tion of the SR5400 is changed.

Note:

•CDR/MD button is set CDR function at initial. To switch MD function, press and hold down CDR/ MD button and press 2 button.

•To return CDR function, press and hold down CDR/MD button and press 1 button.

v MAIN VOLUME UP ( ) /DOWN ( ) buttons Main volume control of the SR5400. The front, sur- round, center and subwoofer channel volumes con- trolled by these buttons simultaneously.

bMUTE button

Muting button of the SR5400. Press this button de- crease the sound temporarily . Press this button again to return to the previous sound.

When this button is pressed, “MUTE” indicator lights up.

nMENU button

(when AMP mode is selected)

This button is used to enter the SETUP MAIN MENU.

mCursor buttons ( , , , , OK)

Used to operate on-screen and other displays used by receivers and other components.

See page 16.

,MENU OFF button

(when AMP mode is selected)

This button is used to exit from the SETUP MAIN MENU.

.Numeric buttons 1 to 9 / Surround mode buttons

Numeric buttons

These buttons are used to enter figures in the selec- tion of a tuner preset station and station name pre- set or to set select a CD track number, etc. The func- tions of these buttons are dependent on the function button selected.

Surround mode buttons (when AMP mode is selected)

These buttons are used to select the surround mode.

⁄0P.SCAN (preset scan) button

(when TUNER mode is selected)

This button is used to start preset scan when SR5400 is selected TUNER mode.

⁄10 / A/D button

0 button

This button is used to enter the number “0”

A/D button (when AMP mode is selected)

This is used to switch between the analog and digital inputs.

⁄2CONTROL buttons

These buttons are used when operating the CD player, TAPE deck, etc.

The function of these buttons are dependent on the function button selected.

For the controllable functions of each input function, please refer to contrable function table on the page 10.

⁄3ATT (attenuator) button

When the input signal is too high and the voice dis- torts even while adjusting the SR5400 VOLUME control, turn on this function. “ATT” is illuminated when this function is activated.

The input level is reduced. Attenuator is invalid for the output signal of “REC OUT”.

Note:

•This function is unavailable while the digital input is selected.

⁄4TREBLE UP () /DOWN () buttons

These buttons are used to adjust the tone control of high frequency sound for left and right speaker.

⁄5BASS UP () /DOWN () buttons

These buttons are used to adjust the tone control of low frequency sound for left, right and subwoofer speaker.

⁄6MEMO button

Memory enable button for various preset functions.

⁄7CLEAR button

This button is used to cancel for certain memory or programming operations.

⁄8DISPLAY button

Selects the display mode for the front display of the SR5400.

⁄9NIGHT button

Pressing this button prevents the Dolby Digital sig- nal from playback at a loud voice. This function re- duces the voice by 1/3 to 1/4 at maximum. Thus, it eliminates the occurrence of an abruptly loud voice at night. However, the function is valid only in the case when the Dolby Digital signal is entered into OPTICAL or COAXIAL and data to compress the voice exists in the signal to be played back.

When this button is pressed, the “NIGHT” indicator is illuminated.

¤0S- (Source) DIRECT button

When this button is pressed, the tone control circuit is bypassed.

¤1SETUP / T.TONE button

(when AMP mode is selected)

Used to enter the test tone menu.

¤2OSD button

(when AMP mode is selected)

When this button is pressed, the current setting is displayed on the TV monitor.

¤3SLEEP (sleep timer) button

This button is used for setting the sleep timer. It can be operated the same way as the button on the unit.

¤4TV VOLUME UP () /DOWN () buttons

These buttons increase or decrease TV’s volume.

ENGLISH

7