Marantz SR5400U manual Programming The Remote, Controller, Tv Vcr Dss Dvd Cd Tape Cdr Md

ENGLISH	PROGRAMMING THE REMOTE
	CONTROLLER
	The remote controller RC5400SR must be
	programmed to use the codes for your appliances
	of different brands. This is done by keying in a 4-
	digit code or by scanning the codes until the
	correct one is found. We recommend to using the
	4-digit code. This mode is faster and more
	reliable. The code scanning method should be
	used only if you cannot find the code for one of
	your appliances. The codes are listed at the end of
	this book.

Important:

•Use the remote control buttons for programming, not the buttons of the receiver or other appliances.

•Some codes may be not match your equipment. In this case, your equipment cannot be controlled with this remote controller.

PROGRAMMING WITH THE 4-DIGIT CODE

							OK
	POWER				1.	SETUP/		MENU OFF
						T.TONE
						S-DIRECT	AUTO		DTS
							1	2	3
	TV	VCR1	DSS/VCR2	DVD		NIGHT	CSII	EX/ES	DSP
							4	5	6
						DISPLAY	M-CH ST	STEREO	6.1CH IN
	TUNER	CD	TAPE	CDR/MD			7	8	9
						CLEAR	MEMO	A/D	P.SCAN
					2.			0
		AUX	AMP					CHANNEL/SKIP
1.	TV			MAIN
	VOL.	SLEEP	MUTE	VOL.		BASS	TREBLE	TUNE/SEARCH
							MODE	DISP./RDS	F.DIRECT
	OSD		MENU
						+/A /ANT	–/B /VCR	ATT.	PTY

1. Press and hold down the function button for the appliance which should be controlled and press SETUP until the indicator blinks twice.

2. Press the 4-digit code for appliance (code table at the end of this book)

3. When the procedure is successful, the indicator will blink twice.

Note:

•If the indicator did not blink twice, then repeat steps 1 through 2 and try entering the same code again.

SCANNING THE CODE TABLE

OSD MENU

	POWER						OK
	TV	VCR1	DSS/VCR2	DVD	2.	SETUP/		MENU OFF
						T.TONE
						S-DIRECT	AUTO		DTS
	TUNER	CD	TAPE	CDR/MD	6.		1	2	3
							4	5	6
						NIGHT	CSII	EX/ES	DSP
		AUX	AMP			DISPLAY	M-CH ST	STEREO	6.1CH IN
							7	8	9
					3.
2.	TV			MAIN		CLEAR	MEMO	A/D	P.SCAN
	VOL.	SLEEP	MUTE	VOL.				0
								CHANNEL/SKIP
	OSD		MENU			BASS	TREBLE	TUNE/SEARCH

1. Switch on the appliance which should be controlled.

2. Press and hold down the function button for appliance which should be controlled and press SETUP until the indicator blinking twice.

3. Press the code 9 - 9 - 1. The indicator will blink twice.

4. Aim the remote control at the appliance and slowly alternate between pressing POWER and the function button for the appliance.

5. Stop when the appliance turns off.

6. Press SETUP once to lock in the code.

CHECKING THE CODE
				1.		OK
POWER
					SETUP/		MENU OFF
				3.	T.TONE
					S-DIRECT	AUTO		DTS
TV	VCR1	DSS/VCR2	DVD			1	2	3
					NIGHT	CSII	EX/ES	DSP
				4.		7	8	9
						4	5	6
TUNER	CD	TAPE	CDR/MD		DISPLAY	M-CH ST	STEREO	6.1CH IN
					CLEAR	MEMO	A/D	P.SCAN
	AUX	AMP		2.			0
TV			MAIN				CHANNEL/SKIP
VOL.	SLEEP	MUTE	VOL.
					BASS	TREBLE	TUNE/SEARCH
OSD		MENU				MODE	DISP./RDS	F.DIRECT

1. Press and hold down the function button for appliance which should be controlled and press SETUP until the indicator blinking twice.

2. Press the code 9 - 9 - 0. The indicator will blink twice.

3. To view the code for first digit, press 1 once. Wait 3 seconds, count the indicator blinks (e.g. 3 blinks = 3) and write down the number.

Note:

If a code digit is “0”, the indicator will not blink.

4. Repeat step 3 three more times for remaining digits. Use 2 for the second digit, 3 for the third digit, and 4 for the fourth digit.

RESETTING THE ALL CODE

OSD MENU

	POWER						OK
	TV	VCR1	DSS/VCR2	DVD	1.	SETUP/		MENU OFF
						T.TONE
						S-DIRECT	AUTO		DTS
	TUNER	CD	TAPE	CDR/MD			1	2	3
						NIGHT	CSII	EX/ES	DSP
							4	5	6
		AUX	AMP			DISPLAY	M-CH ST	STEREO	6.1CH IN
							7	8	9
					2.
1.	TV			MAIN		CLEAR	MEMO	A/D	P.SCAN
	VOL.	SLEEP	MUTE	VOL.				0
								CHANNEL/SKIP

OSD MENU BASS TREBLE TUNE/SEARCH

1. Press and hold down the any function button and press SETUP until the indicator blinking twice.

2. Press the code 9 - 8 - 1. The indicator will blink twice.

Then, RC5400SR will return to the factory preset code.

Note:

•After this procedure, the selected function button is set initial code and other function buttons are set initial code too.

Once you have found and the codes for your vari- ous appliances, you may want to write them down

here.

TV

VCR

DSS

DVD

CD

TAPE

CDR

MD

8