Marantz SR5400U manual Rear Panel, ⁄06.1 Channel Input, VCR2

ENGLISH

REAR PANEL

z x c v b

ANTENNA

COMPONENT VIDEO

DVD

DSS/VCR2

MONI.OUT

Y

CB/PB

CR/PR

Y

CB/PB

CR/PR

Y

CB/PB

CR/PR

FM (75Ω)

GND

AM

VIDEO

VCR1

DSS/VCR2

S-VIDEO

TV

DVD

VCR1

DSS/VCR2

MONI.

TV

DVD

IN

OUT

IN

OUT

MONI.OUT

IN

OUT

IN

OUT

OUT

DIGITAL IN

DIGITAL OUT

RC-5

IN

L

SL

C

PRE

1

2

3

4

OPT.

COAX.

OUT

OUT

R

SR

SB

SW

TV

DVD

VCR1

DSS/VCR2

CD

TAPE

CDR/MD

L

SL

C

6.1CH

L

IN

R

n m

AC IN

SERIAL NO.

SWITCHED UNSWITCHED 1A 120W MAX 1A 120W MAX

AC OUTLETS

120V 60HZ

R L R L

SURROUND

bMONITOR OUT

This is a monitor output and each one includes both composite video and S-video configurations. W h e n c o n n e c t i n g t w o v i d e o m o n i t o r s o r televisions, be aware that the OSD interface can be used with both MONITOR OUT connections.

nAC IN

Connect to an AC power outlet.

SR5400 has to be powered by 120 V AC only.

mAC OUTLETS

Connect the AC power cables of components such as a DVD and CD player to these outlets. SWITCHED and UNSWITCHED outlets are provided.

The one marked SWITCHED provides power only when the SR5400 is turned on and is useful for components which you use every time you play

⁄06.1 CHANNEL INPUT

By connecting a DVD Audio player, SACD multichannel player, or other components that has a multichannel port, you can playback the audio with 5.1 channel or 6.1 channel outputs.

⁄1REMOTE CONT. IN/OUT terminals

Connect to a Marantz component equipped with remote control (RC-5) terminals.

⁄2AUDIO IN/OUT (CD, TAPE, CD-R, TV,

DVD, VCR1, DSS/VCR2)

These are the analog audio inputs and outputs. There are 7 audio inputs (4 of which are linked to video inputs) and 4 audio outputs (2 of which are linked to video outputs). The audio jacks are nominally labeled for cassette tape decks, compact disc players, DVD players and etc.... The

IN	OUT	IN	OUT	IN	OUT	IN	OUT	R	SR	SB	SW
				AUDIO

FRONTCENTER SURROUND

SPEAKER SYSTEMS

MINIMUM 6 OHMS

BACK

your system.

The one marked UNSWITCHED is always live as long as the SR5400 is plugged into a live outlet.

audio inputs and outputs require RCA-type connectors.

⁄3 ⁄2 ⁄1 ⁄0 .

,

A component connected here may be left on permanently, or may be switched off with via its own power switch.

Caution:

⁄3DIGITAL INPUT (Dig.1 - 4) / OUTPUT (coaxial, optical)

These are the digital audio inputs and outputs. There are 2 digital inputs with coaxial jacks, 2 with

zVIDEO IN/OUT (TV, DVD, VCR1, DSS/

VCR2)

These are the video inputs and outputs. There are 4 video inputs and 2 video outputs and each one includes both composite video and S-video configurations. Connect VCRs, DVD players, and other video components to the video inputs.

S-video sources can be viewed through the S- video outputs, and composite sources can only be viewed through the composite output.

The 2 video output channels can be used to be connected to video tape recorders for making recordings.

xFM antenna terminal (75 ohms)

Connect an external FM antenna with a coaxial cable, or a cable network FM source.

AM antenna and ground terminals

Connect the supplied AM loop antenna. Use the terminals marked “AM” and “GND”. The supplied AM loop antenna will provide good AM reception in most areas. Position the loop antenna until you hear the best reception.

cCOMPONENT VIDEO INPUT/OUTPUT

If your DVD player or other device has component video connectors, be sure to connect them to these component video connectors on the SR5400. The SR5400 has two component video input connectors to obtain the color information (Y, CB, CR) directly from the recorded DVD signal or other video component and one component video output connector to output it directly into the matrix decoder of the display device.

By sending the pure DVD component video signal directly, the DVD signal forgoes the extra processing that normally would degrade the image. The result is vastly increased image quality, with incredibly life like colors and crisp detail.

Notes:

•This component video output will not display the OSD menu system.

v Preamp Outputs (L, R, SL, SR, SB, C) Jacks for L(front left), R (front right), C (Center), SL (surround left), SR (surround right) and SB (surround back).

Use these jacks for connection to external power amplifiers.

•In order to avoid potential turn-off thumps, anything plugged into these outlets should be powered up before the SR5400 is turned on.

•The capacity of this AC outlet is 120W. Do not connect devices that consume electricity more than the capacity of these AC outlets. If the total power consumption of the connected devices exceeds the capacity, the protection circuit shuts down the power supply.

,Speaker outputs terminals

Six terminals are provided for the front left, front right, front center, surround left, surround right and surround back speakers.

.Subwoofer Output

Connect this jack to the line level input of a powered subwoofer. If an external subwoofer amplifier is used, connect this jack to the subwoofer amplifier input. If you are using two subwoofers, either powered or with a 2 channel subwoofer amplifier, connect a “Y” connector to the subwoofer output jack and run one cable from it to each subwoofer amplifier.

optical jacks.

The inputs accept digital audio signals from a compact disc, LD, DVD, or other digital source component.

For digital output, there is 1 coaxial output and 1 optical output.

The digital outputs can be connected to MD recorders, CD recorders, DAT decks, or other similar components.

6