Marantz SR5400U manual This mode bypasses all surround processing

ENGLISH

MULTI CH. ST

This mode is used to create a wider, deeper and more natural soundstage from two channel source material.

This is done by feeding the left channel signal to both left front and left surround speaker and the right channel signal to both right front and right surround speaker. Additionally, the center channel reproduces a mix of the right and left channel.

CIRCLE SURROUND II (CSII-CINEMA, CSII-MUSIC, CSII-MONO)

Circle Surround is designed to enable multi- channel surround sound playback of non-encoded and multi-channel encoded material.

Backward compatibility provides listeners with up to

6.1channels of surround performance from your entire collection of music and film, including broadcast, videotape and stereo recorded music.

Depending on source material, you can select CSII- Cinema mode, CSII-Music mode or CSII-Mono mode.

Note:

•CS II mode is available for 2ch input signals which are encoded in Dolby Digital or PCM format.

•PCM-audio signals can be subjected to Pro Logic processing when the sampling frequency is 32 kHz, 44.1 kHz or 48 kHz.

VIRTUAL

This mode creates a virtualized surround sound experience from a two-speaker (front L and R) playback system playing any multi-channel audio source (such as found on DVDs and digital broadcasts), including Dolby Digital, Dolby Pro Logic or DTS.

STEREO

This mode bypasses all surround processing.

In stereo program sources, the left and right channels play normally when PCM-audio or analog stereo is input.

With Dolby Digital and DTS sources, the 5.1 multi- channels are converted to two channel stereo. 96 kHz PCM source material can be played back in stereo mode.

S (SOURCE ) - DIRECT

In the source direct mode, the tone control circuit and bass management configuration are bypassed for full range frequency response and the purist audio reproduction.

96 kHz PCM source material can be played back in this mode.

Notes:

•Internal speaker size is setup to front L/R = Large, Center = Large, Surround L/R = Large and Subwoofer = Yes automatically. Tone controls and additional processing are also defeated.

•When you use this mode with certain DVD and CD players, performing operations such as “Skip” or “Stop” may momentarily interrupt the output.

CAUTION

NOTE for DTS signal

*Connected DVD-player, laser-disc player or CD- player needs to support DTS-digital output. You may not be able to play some DTS source signals from certain CD players and LD players even if you connect the player to the SR5400 digitally. This is because the digital signal has been processed (such as the output level, sampling frequency, or frequency response) and the SR5400 cannot recognize the signal as DTS data.

*Depending on the player used, DTS play may produce a short noise. This is not a malfunction.

*While signals from DTS-laser disc or CD are playing in another Surround mode, you cannot switch to digital input or from digital input to analog input by INPUT SETUP in SETUP MAIN MENU or the A/D button.

*The outputs for the VCR 1 OUT, DSS/VCR 2 OUT, TAPE OUT, and CD-R OUT output analog audio signals. Do not record from CDs or LDs that support DTS using these outputs. If you do, the DTS-encoded signal will be recorded as noise.

NOTE for Dolby Digital Surround EX signal

*When playing Dolby Digital Surround EX- encoded software in 6.1 channels, it is required to set the EX/ES mode.

*Note that some of Dolby Digital Surround EX- encoded software does not contain the identification signal. In this case, set the EX/ES mode manually.

NOTE for 96kHz PCM audio

*AUTO, Source- DIRECT, and STEREO modes can be used when playing PCM signals with a sampling frequency of 96 kHz (such as from DVD-Video discs that contain 24 bit, 96 kHz audio). If such signals are input during playback in one of the other surround modes, output from SR5400 will be muted.

*Certain DVD player models inhibit digital output. For details, refer to the player’s operation manual.

*Some DVD formatted discs feature copy protection. When using such discs, 96 kHz PCM signal is not outputted from the DVD player. For details, refer to the player's operation manual.

22