ENGLISH | ADVANCED CONNECTING |
|
CONNECTING THE REMOTE CONTROL JACKS
| R L | R L R L |
DVD AUDIO PLAYER |
| R L R L R L |
|
| |
or |
|
|
SACD MULTI CHANNEL PLAYER | COMPONENT VIDEO |
|
MONITOR OUT |
|
|
| ANTENNA |
|
|
| COMPONENT VIDEO |
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
| MONITOR OUT |
| ||||
|
|
|
|
|
| Y | CB/PB | CR/PR | Y | CB/PB | CR/PR | Y | CB/PB | CR/PR |
|
FM (75Ω) | GND | AM |
|
|
|
|
|
|
|
|
|
|
|
| |
VIDEO |
|
|
|
|
|
|
|
|
| VCR1 | DSS/VCR2 |
| |||
TV | DVD |
| VCR1 | DSS/VCR2 | MONITOR | MULTI |
|
| MONITOR |
| |||||
IN | TV | DVD | IN | OUT | IN | OUT | OUT |
| |||||||
|
| OUT | IN | OUT | OUT | OUT |
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| RS- |
|
|
|
|
|
|
|
|
| MULTI |
| FLASHER |
|
|
| 2 |
|
|
|
|
|
|
|
| RC |
| IN | L | SL | SBL | C | |
|
| DIGITAL IN |
|
| DIGITAL OUT |
|
| IN |
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
| ||||
1 | 2 | 3 | 4 | 5 | 6 | OPT. | COAX. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| PRE |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| OUT |
|
|
|
|
|
|
|
|
|
| OUT |
| R | SR | SBR | SW |
|
|
|
|
|
|
|
|
|
|
| DC OUT | ||||
NO.SR7400
RL
BACK /
SPEAKER
| SWITCHED UNSWITCHED |
AC IN | 1A 120W MAX 1A 120W MAX |
AC OUTLETS
120V 60HZ
RC OUT
CR/PRY CB/PB CR/PRY CB/PB CR/PR | CENTER |
| |
L |
TV | DVD | VCR1 | DSS/VCR2 | CD | TAPE | CDR/MD | MULTI | L | SL | SBL | C |
L
7.1CH
RLRL | R L | OPTION |
|
|
|
|
| VCR1 | DSS/VCR2 | MONITOR | |
TV | DVD | IN | OUT | IN | OUT | OUT |
R
IN
FRONT A | FRONT B | CENTER | SURROUND |
IN | OUT | IN | OUT | IN | OUT | IN | OUT OUT | R | SR | SBR SW |
|
|
|
| AUDIO |
|
|
| (AUX2) |
|
|
SYSTEMS
A OR B, CENTER, SURROUND, SURR. BACK : MINIMUM 6 OHMS
A AND B : MINIMUM 8 OHMS
L
R
FRONT SURR.
|
|
|
|
|
|
| RS | R |
|
| RC | IN | L | SL | SBL | C | FRONT SURR. SURR. | SUB | |
| BACK | WOOFER | |||||||
|
| MULTI | FLASHER |
|
|
|
|
|
|
|
| IN |
|
|
|
|
|
|
|
| . |
|
|
|
|
|
| POWER |
|
| CENTER |
|
|
|
|
| OUT |
| |
|
|
|
|
|
|
| PRE |
|
|
|
| OUT | DC OUT | R | SR | SBR | SW | AMPLIFER |
|
| TAPE | CDR/MD | MULTI | L | SL | SBL | C |
|
|
SURR. | SUB |
|
|
|
|
| 7.1CH | Subwoofer |
|
BACK | WOOFER |
|
|
|
|
| IN |
|
|
| OUT | IN OUT | OUT | R | SR | SBR | SW |
|
|
(AUX2)
R L R L R L
L R L R L R
Front | Center | Front | |
Left | Right | ||
| |||
Surround | Surround | ||
Left |
| Right | |
Surround |
| Surround | |
Back Left |
| Back Right | |
1
REMOTE | CD RECORDER | REMOTE | MD DECK | REMOTE | CD PLAYER |
CONTROL |
| CONTROL |
| CONTROL |
|
IN |
| IN |
| IN |
|
OUT |
| OUT |
| OUT |
|
| EXTERNAL INTERNAL |
| EXTERNAL INTERNAL |
| EXTERNAL INTERNAL |
CONNECTING MULTI CHANNEL AUDIO SOURCE
The 7.1CH INPUT jacks are for multichannel audio source such as a SACD multichannel player, DVD audio player or external decoder.
If you use these jacks, switch on the 7.1CH INPUT and set the 7.1CH INPUT level by using the SETUP MAIN MENU. See page 21.
CONNECTING AN EXTERNAL POWER AMPLIFIER
The PREOUT jacks are for connecting external power amplifiers.
Be sure to connect each speaker to the corresponding external power amplifier.
q
You can control other Marantz products through this unit with the remote control by connecting the REMOTE CONTROL terminals on each unit.
The signal transmitted from the remote control is received by the remote sensor on this unit. Then the signal is sent to the connected device through this terminal. Therefore you need to aim the remote signal only to the unit. Also, if a Marantz power amplifier (some models excluded) is connected to one of these terminals, the power amplifier’s, power switch is synchronized with this unit’s power switch.
Set the REMOTE CONTROL SWITCH on the units, other than the main unit to EXT.(EXTERNAL) for this feature.
w
Whenever external infrared sensors or similar devices are connected to
1. Hold down the SELECT button and TV button on the front panel at the same time for five seconds.
2. The setting “IR=ENABLE” is shown on the FL DISPLAY.
3. Press the SELECT button to change this to “IR=DISABLE”.
4. Press the ENTER button. Once this setting is made, the infrared sensor on the main unit is disabled.
Note:
Be sure to set to “IR=ENABLE” when external infrared sensors or similar devices are not connected. Otherwise, the main unit will be unable to receive remote control commands.
5. To restore the original setting, perform steps 1 to 4 to set to “IR=ENABLE”.
14
