ENGLISH | BASIC OPERATION | |
(PLAY BACK) | ||
|
VIDEO CONVERT
When this function is activated, the video or S- video signal can be emitted from the video, S- video or component video output terminal.
To activate this function, select VIDEO CONVERT in PREFERENCE menu and set ENABLE.
Notes of OSD menu: | ADJUSTING THE MAIN VOLUME |
|
•The setup menu can be displayed through all video out (COMPONENT,
• The setting informations (e.g. volume setting) are |
|
|
displayed through all video out when the VIDEO | VOLUMEVOLUME |
|
CONVERT function are set ENABLE. | CH | VOLVOL |
|
|
SELECTING AN INPUT SOURCE
Before you can listen to any input media, you must first select the input source on the SR7400.
Example : DVD
ER SR7400
|
|
|
|
|
|
| TV | DVD | VCR | DSS |
CLEAR |
| MEMORY | TUNING |
| F/P |
| MODE |
|
|
|
|
|
|
|
|
|
| TUNER | CD | MD | |
|
|
|
|
|
|
| TAPE | AUX1 | AUX2 | AMP |
TV | DVD | VCR1 DSS/VCR2 | AUX1 | TAPE | CD | TUNER |
|
|
| |
|
|
|
|
|
|
|
|
| LIGHT |
|
|
|
|
|
|
|
| 1 |
|
| 2 |
RC1400
Learning Remote Controller
Notes :
• The component video signal is emitted only from |
component video output terminal. |
When the video equipment is connected by |
component terminal, connect the monitor and |
SR7400 by the component terminal. |
• This function is unavailable for the REC out |
terminal. |
• This function is unavailable for the still picture, |
fast forward and reverse playing of the video |
component. |
• If the picture has a noise with this function, the |
combination of the monitor, SR7400 and the |
Note: no setting information is displayed when the signal is emitted from the COMPONENT IN
to COMPONENT OUT.
• The setting informations (e.g. volume setting) are displayed through the
SELECTING THE SURROUND MODE
| F/P | MODE | DOWNDOWN | UPUP |
|
|
|
|
|
|
| OK |
|
|
|
|
| MUTE |
|
|
TAPE | CD | TUNER |
|
|
| |
|
|
|
| AUX1 INPUT |
|
|
|
|
|
| PREV |
| MUTE |
|
|
|
|
| GUIDE |
|
|
|
|
| MENU |
| EXIT |
|
|
|
| TEST | CH.SEL | SURR |
|
|
|
| 1 | 2 | 3 |
|
|
|
| 7 1CH | ATT |
Adjust the volume to a comfortable level using the VOLUME control knob on the front panel or VOL +
/– buttons on the remote.
To increase the volume, turn the VOLUME knob clockwise or press VOL + button on the remote, to decrease the volume, turn counterclockwise or
To select DVD, simply press the DVD button on the front panel or press the DVD button on the remote. After you have selected DVD, simply turn on the DVD player and play the DVD.
video component may be not compatibile. |
In this case, VIDEO CONVERT function must be |
set DISABLE. |
Example :
Monitor is connected with the component.
Example : AUTO SURROUND
AV SURROUND RECEIVER SR7400
SELECTOR
CLEARMEMORY
SELECT | ENTER |
PAGE 1 2 3 4
M
D1D1
D2
D3
D4
D5D5
press VOL – button on the remote.
Notes:
• The volume can be adjusted within the range of – ∞ |
to 18 dB, in steps of 1 dB. |
• However, when the channel level is set as described |
on page 19, if the volume for any channel is set at |
+1 dB or greater, the volume cannot be adjusted up |
to 18 dB. |
• As the input source is changed, the new input |
name will appear momentarily an OSD information |
on the video display. The input name will also |
TV | DVD | VCR1 | DSS/V |
POWER ON/STANDBY | PHONES |
CHVOL
(In this case the maximum volume adjustment |
range is “18 dB - Maximum value of channel level) |
appear in the display, on the |
• As the input is changed, the SR7400 will |
automatically switch to the digital input, surround |
mode, attenuation, and night mode status which |
were entered during the configuration process |
for that source. |
• When an audio source is selected, the last video |
input used remains routed to the VCR1 & DSS/ |
VCR2 Outputs and Monitor Output. This permits |
simultaneous viewing and listening to different |
sources. |
TUNER | CD | MD | |
TAPE | AUX1 | AUX2 | AMPAMP |
|
| LIGHT |
|
1 |
|
| 2 |
|
| RC1400 |
|
| Learning Remote Controller |
|
(Using the SR7400)
To select the surround mode during playback, turn the SELECT knob on the front panel.
(Using the remote control unit)
To select the surround mode, press the AMP button and press the > button until PAGE1 is displayed. Press the AUTO (D1) button.
ADJUSTING THE TONE (BASS &
TREBLE) CONTROL.
M
|
|
| D1 |
| AV SURROUND RECEIVER SR7400 |
|
|
| SELECTORSELECTOR |
| D2D2 |
|
|
| D3D3 |
| CLEAR | MEMORY | D4D4 |
|
| PAGE | 3 |
|
|
| D5D5 |
SELECTSELECT | ENTER |
|
|
• When a Video source is selected, the video signal |
for that input will be routed to the Monitor Output |
jacks and will be viewable on a TV monitor |
connected to the SR7400. |
If a component video input is connected to the |
DVD or DSS component inputs, it will be routed |
to the Component Video Output. Make certain |
that your TV is set to the proper input to view the |
signal. |
VIDEO |
|
or | component |
or component |
|
Monitor is connected with the video or
VIDEO | VIDEO |
or | or |
| VIDEO |
component | or |
The signal cannot be converted from the component to the video or
TV | DVD | VCR1 | DSS/VC |
POWER ON/STANDBY | PHONES |
CHVOL
TUNER | CD | MD | |
TAPE | AUX1 | AUX2 | AMPAMP |
|
| LIGHT |
|
1 |
|
| 2 |
|
| RC1400 |
|
| Learning Remote Controller |
|
During a listening session you may wish to adjust the Bass and Treble Control to suit your listening tastes or room acoustics.
(Using the SR7400)
To change the selector mode , press the SELECT button, until "BASS" or "TREBLE" is shown on the front display.
Turn the SELECTOR knob to the desired level of tone control.
22