•If the copying fails in the middle of the copying process, ERROR is displayed on the remote control.
Check and perform steps 1 to 7 again.
11.Once copying is completed, press the M button on both remote controls.
SETUP
SETTING THE LIGHTING TIME
•The LCD lights up when the LIGHT buttons are pressed. The LCD remains lit while the pressed button is held down, and it goes off when the button is released.
•The LCD continues to light up if another button is pressed while it is lit or if pressed within two seconds after the light goes off.
•The lighting time can be set in
The LIGHT buttons have light - absorbing properties that enable them to store light. If the buttons are no longer illuminated in a dimly lit environment, bring the buttons near a fluorescent lamp or other light source for a sufficient amount of time. This should illuminate the buttons again.
•The LIGHT buttons consist of a LIGHT1 and LIGHT2 button, and they both perform the same operation.
The factory default lighting time is set to 15 seconds.
This example shows how to set the lighting time to 20 seconds.
2 | 3 |
|
|
|
| 4 |
|
|
|
| LEARN |
|
|
|
| LEARN |
|
|
|
PAGE 1 | 2 | 1 | 2 | 3 | 4 | 1 | 2 | 3 | 4 |
1. Hold down the M button for three seconds or
more.
The menu is displayed.
2. Press the > button to display the second page
SETUP menu.
3. Press the D1 (LIGHT) direct button .
The LIGHT is displayed on the LCD
4. Press the 
or 
cursor button to set the lighting time.
5. Press the OK cursor button to enter the lighting time.
6. Once the setting is finished, press the M button .
SETTING THE MACRO INTERVAL TIME
When a macro program is executed, control signals are transmitted in sequence. This transmission interval (interval time) can be set in
If the interval time is set in this Setup mode, the interval times for all programmed macros are changed. If necessary, use EDIT (see page 37) in the macro program to change the individual transmission times.
The factory default setting for the transmission interval is 1 second.
This example shows how to set the interval time to 5 seconds.
2 | 3 |
|
|
|
| 4 |
|
|
|
| LEARN |
|
|
|
| LEARN |
|
|
|
PAGE 1 | 2 | 1 | 2 | 3 | 4 | 1 | 2 | 3 | 4 |
1. | Hold down the M button for three seconds or |
| more. |
2. | The menu is displayed. |
Press the > button to display the second page | |
3. | SETUP menu. |
Press the D2 | |
4. | Press the or cursor button to set the |
| interval time. |
| Holding down the cursor button |
5. | time indicator. |
Press the OK cursor button to enter the | |
6. | interval time. |
Once the setting is finished, press the M |
button .
ADJUSTING THE DISPLAY CONTRAST
The contrast of the LCD can be adjusted. Adjust for maximum visibility according to your viewing environment.
2 | 3 |
|
|
|
| 4 |
|
|
|
| LEARN |
|
|
|
| LEARN |
|
|
|
PAGE 1 | 2 | 1 | 2 | 3 | 4 | 1 | 2 | 3 | 4 |
1. Hold down the M button for three seconds or more.
The menu is displayed.
2. Press the > button to display the second page SETUP menu.
3.Press the D3 (CONT) direct button .
4.Press the 
or 
cursor button and set the display contrast for maximum visibility.
The adjustment has 10 levels.
The factory default setting for the contrast is the fifth level.
5.Press the OK cursor button to enter the display contrast.
6.Once the setting is finished, press the M button .
ENGLISH
39
