Marantz SR7400 manual Basic Operation Tuner

ENGLISH

BASIC OPERATION

(TUNER)

LISTENING TO THE TUNER

Frequency scan step for AM is selectable.

MANUAL TUNING

3.2. 1.

R	MEMORY		TUNING		F/P	MODE	DOWN
							MUTE
DVD	VCR1	DSS/VCR2	AUX1	CD-R	TAPE	CD	TUNER

SOURCE

PAGE 2

M

D1

D2

D3

D4

D5

(FM) TUNING MODE (AUTO STEREO OR MONO)

3.M

						D1
					VOLUME	D2
3.						D3
	G	F/P	MODE	DOWN	UP	D4D4
2.						PAGE 1
						D5D5
					MUTE
	CD-R	TAPE	CD	TUNER
					AUX1 INPUT
					CH	VOL

1. To select FM , press the TUNER button on the front panel.

2. While pressing the MEMORY button, press the TUNINGbutton up.

“AUTO PRESET” will appear on the display, and scanning starts from the lowest frequency.

3. Each time the tuner finds a station, scanning will pause and the station will be played for

Default setup is 10 kHz step, if your country’s standard is 9 kHz step, Press TUNER button on

TUNER CD CD-R

TAPE AUX1 AUX2

MD

AMP

1.	TV	DVD	VCR	DSS
	TUNERTUNER	CD	CD-R	MD

five seconds.

During this time, the following operations are

the remote more than 6 seconds. Scan step will change.

Note:

•Preset memory for the tuner will clear by changing this setup.

LIGHT

1 2

RC1400

Learning Remote Controller

(Using the SR7400)

1. To select tuner and desired band (FM or AM),

press the TUNER button on the front panel

2. Press the F/P (Frequency/Preset) button on

front panel, to have the frequency appear on the

TAPE AUX1 AUX2 AMP

When in the auto stereo mode, AUTO indicator will be illuminated on the display.

The “ST” indicator is illuminsted when a stereo broadcast is tuned in.

At open frequencies, the noise is muted and the “TUNED” and “ST” indicators are not illuminated.

possible.

The band can be changed by the TUNER button.

4. If no button is pressed during this period, the

current station is memorized in location Preset

02.

If you wish to skip the current station, press the

AUTO TUNING

3.2. 1.

DOWN

R MEMORY TUNING F/P MODE

MUTE

SOURCE

PAGE 2

M

D1

D2

D3

D4

D5

3.

3.

2.

display.

3. Press the TUNINGorbuttons.

(Using the remote control unit)

1. To select tuner and desired band (FM or AM), press the TUNER button twice within two seconds on the remote.

If the signal is weak, it may be difficult to tune into the station in stereo. In such a case, press the MODE button on the front panel.Or press the TUNER button and press the the > button until PAGE1 is displayed. Press the T-MODE (D4) button.

“AUTO” indicator is not illuminated, if FM stereo broadcasts are received in monaural and the “ST”

TUNING button during this period, this station is skipped and auto presetting continues.

5. Operation stops automatically when all 50 preset memory positions are filled or when auto scanning attains the highest end of all bands. If you desire to stop the auto preset memory at anytime, press the CLEAR button.

DVD VCR1 DSS/VCR2 AUX1 CD-R TAPE CD TUNER

TUNER	CD	CD-R	MD	1.
TAPE	AUX1	AUX2	AMP
		LIGHT
1			2
		RC1400

2. Press the > button until PAGE2 is displayed

3. Press the SCAN+ (D1) or SCAN– (D2) button to tune in the deseired station.

indicator is not illuminated.

To return to auto stereo mode, press the MODE button or press T-MODEbutton on the remote again.

MANUAL PRESET MEMORY

Learning Remote Controller

(Using the SR7400)

1. To select tuner and desired band (FM or AM), press the TUNER button on the front panel.

2. F/P button on the front panel to display the frequency.

3. Press the TUNINGorbutton on the front panel for more than 1 second to start the Auto tuning function.

DIRECT FREQUENCY CALL

PREV		MUTE	2.
	GUIDE
MENU		EXIT
TEST	CH.SEL	SURR
1	2	3	3.
7.1CH	ATT	SPK-AB
4	5	6
DISP	OSD	SLEEP
7	8	9
CLEAR	0	MEMO

AUTO indicator is illuminated the display.

PRESET MEMORY

With this unit you can preset up to 50 FM/AM stations in any order.

For each station, you can memorize the frequency and reception mode if desired.

2. 4.						3.
RECEIVER SR7400
	CLEAR	MEMORYMEMORY		TUNINGTUNING		F/P	M
TV	DVD	VCR1	DSS/VCR2	AUX1	CD-R	TAPE	CD
S

PREV		MUTE
	GUIDE
MENU		EXIT
TEST	CH.SEL	SURR
11	22	33	3.
7.1CH	ATT	SPK-AB
44	55	66
DISP	OSD	SLEEP
77	88	99	2.
CLEAR	00	MEMOMEMO

4. Automatic searching begins then stops when a station is tuned in.

TUNER CD CD-R MD

AUTO PRESET MEMORY

(Using the SR7400)

(Using the remote control unit)

1. To select tuner and desired band (FM or AM), press the TUNER button twice within two seconds on the remote.

2. Press the > button until PAGE2 is displayed.

3. Press and hold the SCAN+ (D1) or SCAN– (D2) button for 1 second or more.

4. Automatic searching begins then stops when a station is tuned in.

If tuning does not stop at the desired station, use to the “Manual tuning” operation.

TAPE	AUX1	AUX2	AMP	1.
		LIGHT
1			2
		RC1400
	Learning Remote Controller

1. To select tuner and desired band (FM or AM), press the TUNER button twice within two seconds on the remote.

2. Press the GUIDE on the remote, display will show “FREQ - - - -”.

3. Input your desired station’s frequency with the ten numbered keypad on the remote.

4. The desired station will automatically be

tuned.

This function automatically scans the FM and AM band and enters all stations with proper signal strength into the memory.

5.	2.	2.4.			1. 3.
SELECTOR
	CLEARCLEAR	TUNINGTUNING	F/P	MODE	DOWN	UP
TV	DVD	VCR1	TAPE	CD	TUNERTUNER

AUX1 INPUT

1. Tune into the radio station you desire (Refer to the “MANUAL TUNING” or “AUTO TUNING” section).

2. Press the MEMORY button on the front panel. “– –“ (preset number) starts blinking on the display.

3. Select the preset number by pressing the

TUNINGorbutton, while this is still blinking (approx. 5 seconds)

4. Press the MEMORY button again to enter. The display stops blinking.

The station is now stored in the specified preset

memory location.

28