GAS CONVERSION KITS

WARNING

This conversion kit shall be installed by a qualified service agency in accordance with the manufacturer's instructions and all applicable codes and requirements of the authority having jurisdiction. If the information in these instructions is not followed exactly, a fire, explosion or production of carbon monoxide may result causing property damage, personal injury or loss of life. The installation is not proper and complete until the operation of the converted appliance is checked as specified in the owner instructions supplied with the kit.

The qualified service agency performing this installation assumes responsibility for this conversion.

AVERTISSEMENT

Cet Équipement de conversion sera installÉ par une agence qualifiÉe de service conformÉment aux instructions du fabricant et toutes exigences et codes applicables de l’autorisÉs avoir la juridiction. Si l’information dans cette Instruction n’est pas suivie exactement, un feu, explosion ou production de protoxyde de carbone peut rÉsulter le dommages causerdepropriÉtÉ,perteoublessurepersonnellede vie. L’agence qualifiÉe de service est esponsable de l’installation propre de cet Équipment. L’installation n’est pas propre et complÉte jusqu’à l’opÉration de l’appareil converti est chÉque suivant les critères Établis dans les instructions de propriÉtaire provi- sionnÉes avec l’Équipement.

In Canada:

THE CONVERSION SHALL BE CARRIED OUT IN ACCORDANCE WITH THE REQUIREMENTS OF THE PROVINCIAL AUTHORITIES HAVING JURISDICTION AND IN ACCORDANCE WITH THE REQUIREMENTS OF THE CAN1-B149.1

AND .2 INSTALLATION CODE.

LA CONVERSION DEVRA ÊTRE EFFECTUÉE CONFORMÉMENT AUX RECOMMANDA- TIONS DES AUTORITÉS PROVINCIALES AYANT JURIDICTION ET CONFORMÉMENT AUX EXIGENCES DU CODE D'INSTALLATION CAN1-B149.1 ET.2.

Gas conversion kits are available to adapt the appliance from the use of one type of gas to the use of another. These kits contain all the necessary components needed to complete the task including labeling that must be affixed to ensure safe operation.

Kit part numbers are listed here and the following steps detail the conversion procedure.

Step 1. Turn off the gas supply to the appliance. Remove the front glass door/frame from the appliance. Access the control compartment.

Step 2. Carefully remove the logs. Exercise care so as not to break the logs.

Step 3. Locate the screws securing the burner assembly to the appliance. Remove the burner assembly and retain the securing screws.

Millivolt SIT SystemsNatural Gas To Propane GasConversion Kits

Models

Cat. No.

MPB-3328H2009MPB-3530H2011MPB-4035H2013MPB-4540H2015

Millivolt SIT Systems

Propane to Natural Gas

Conversion Kits

Models

Cat. No.

MPB-332819M43MPB-3530H2012MPB-4035H2014MPB-4540H2016Step 4. Millivolt Appliances - SIT Systems

a. Refer to Figure 39 and the instructions provided with the kit. Using a Torx T20, remove and discard the three pressure regulator mounting screws. Remove the pressure regulator, spring, poppet, diaphragm and bushing. Discard all removed components. Ensure the rubber gasket installed on the back of the replacement pressure regulator is properly positioned and install the new pressure regulator using the new screws supplied with the kit. Tighten screws to 25 In. lb. torque.

Electronic HONEYWELL Systems

Natural Gas To Propane Gas

Conversion Kits

Models

Cat. No.

MPB-332826M59MPB-353026M60MPB-403526M61MPB-454026M62Electronic HONEYWELL SystemsPropane Gas To Natural Gas

Conversion Kits

Models

Cat. No.

MPB-332819M45MPB-353026M64MPB-403526M65MPB-454026M66SIT Millivolt Gas Valve

Pressure

Regulator

Remove

These

Components

Figure 39

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

19