Safety Regulatory Compliance | Maxtor 6800 instruction

PRODUCTSPECIFICATIONS

EMC/EMI

Radiated Electromagnetic Field Emissions - EMC Compliance

The hard disk drive mechanism is designed as a subassembly for installation into a suitable enclosure and is therefore not subject to Subpart J of Part 15 of FCC Rules (47CFR15) or the Canadian Department of Communications Radio Interference Regulations. Although not required, the disk mechanism has been tested within a suitable end-use product and found to comply with Class B limits of the FCC Rules and Regulations of the Canadian Department of Communications.

The CE Marking indicates conformity with the European Union Low Voltage Directive (73/23/EEC) when the disk mechanism is installed in a typical personal computer. Maxtor recommends that testing and analysis for EMC compliance be performed with the disk mechanism installed within the user's end-use application.

Canadian Emissions Statement

This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the radio interference regulations of the Canadian department of communications.

Le present appareil numerique n'emet pas de bruit radioelectriques depassant les limites applicables aux appareils numeriques de Class B prescrites dans le reglement sur le brouillage radioelectrique edicte par le ministere des communications du Canada.

Safety Regulatory Compliance

All Maxtor hard drives comply with relevant product safety standards such as CE, CUL, TUV and UL rules and regulations. As delivered, Maxtor hard drives are designed for system integration before they are used.

3 – 5

Image 21

Maxtor 6800 manual Safety Regulatory Compliance, Radiated Electromagnetic Field Emissions EMC Compliance

Contents

HA RD Drive Produc T MA Nual DiamondMax U T I O N Before You Begin Contents Handling and Installation Product Specifications Host Software Interface AT Interface Description Interface Commands Service and SupportGlossary Figures Maxtor Corporation IntroductionManual Organization Abbreviations Conventions Signal ConventionsKey Words Numbering Product Description DiamondMax 6800 Key Features Functional / Interface Product Features Logical Block Addressing On-the-Fly Hardware Error Correction Code ECCDefect Management Zone DMZ Software ECC Correction Cache Management Read-Ahead ModeBuffer Segmentation Automatic Write Reallocation AWR Major HDA Components Jumper Location/Configuration Subsystem ConfigurationCylinder Limitation Dual Drive Support Drive Configuration Product SpecificationsPerformance Specifications Models and Capacities Parameter Standard Metric Physical Dimensions Power Mode Definitions Power RequirementsEPA Energy Star Compliance Environmental Limits Shock and Vibration Reliability Specifications Safety Regulatory Compliance Radiated Electromagnetic Field Emissions EMC ComplianceCanadian Emissions Statement Hard Drive Handling Precautions Handling and InstallationPre-formatted Drive Important Notice Multi-pack Shipping Container Unpacking and Inspection Physical Installation Recommended Mounting ConfigurationRepacking Tools for Installation Handling PrecautionsSystem Requirements Drive Identification Information Hard Drive Identification General Requirements Installing 5.25-inch Mounting Brackets and Rails Systems Using Cable SelectInstalling in a Device Bay Mounting Drive in System Attaching System Cables Attaching Interface and Power Cables System Setup Setting the Bios CmosBios Cmos Parameters Hard Drive Preparation System Hangs During Boot Interface Connector AT Interface DescriptionPin Description Summary Pin Description Table PIN Name Signal Name Signal Description PIO Timing Timing Parameters Mode DMA Timing Ultra DMA Timing Mode MIN MAX Sustained Ultra DMA Data In Burst Device Terminating an Ultra DMA Data In Burst Initiating an Ultra DMA Data Out Burst Device Pausing an Ultra DMA Data Out Burst Device Terminating an Ultra DMA Data Out Burst Features Register Error RegisterHost Software Interface Task File Registers Sector Number Register Sector Count RegisterCylinder Number Registers Device/Head Register Command Register Summary Command Name Command Code Parameters Used SDH Alternate Status Register Control Diagnostic RegistersDevice Control Register Digital Input Register Reset and Interrupt Handling Reset HandlingInterrupt Handling Set Feature Commands Interface Commands Read Commands Read SectorsRead Verify Sectors Read Multiple Read DMA Set Multiple Mode Write CommandsWrite Sectors Write Verify Sectors Write DMA Write Multiple Set Features Mode Set Feature Commands Power Mode Commands Sleep Mode Identify Drive Initialization Commands 15-8 = PIO data transfer mode = Write Cache enabled Initialize Drive Parameters Seek, Format and Diagnostic Commands Execute Drive DiagnosticFormat Track Execute S.M.A.R.T A.R.T. Command Set Service Policy Service and SupportNo Quibble Service Support MaxFax Service Customer ServiceInternet Glossary Access Time Cylinder Zero Gigabyte GB Logical Block Addressing Read Gate Signal THIN-FILM Media